Grizzly G0704 owner manual Maintenance, Schedule, Lubrication

Page 38

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Daily Check:

•Make sure mill/drill is disconnected from power when not in use.

•Check for loose mounting bolts.

•Make sure mill/drill is clean and lubricated.

•Check for worn or damaged wires.

•Check for any other unsafe condition.

Monthly Check:

•Check that gibs are adjusted properly.

Biannual Check:

•Lubricate headstock lead screw and gears.

Lubrication

Regular lubrication will ensure your mill/drill per- forms at its highest potential. Regularly wipe all sliding surfaces with Primrose® Way Oil (Page 34) or a light machine oil, then move the components back and forth several times to ensure smooth movements (Figures 44–46). Every six months, or more often with heavy use, clean and lubricate the leadscrews and vertical handwheel ring & pin- ion gears, as outlined on Page 38.

Protect other unpainted cast iron surfaces with regular applications of products like G96® Gun Treatment, SLIPIT®, or Boeshield® T-9.

-36-

Figure 44. Vertical way lube location (both

sides).

Figure 45. Cross way lube locations.

Figure 46. Longitudinal way lube locations.

Model G0704 (Mfg. since 09/09)

Image 38

Contents Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification Electronic Controls Identification G0704 electronic controls identificationMachine Data Sheet Other Features Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftUnpacking SetupNeeded for Setup Description QtyNot Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsDrill Chuck Arbor AssemblyTo install the drill chuck onto the arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsSpeed Range Selector Knob Selects low range OperationsBasic Controls Digital readout unit controls Operation Overview Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckTo remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed H8177-Worktable with Angle AccessoriesH8179 H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base G5758-Tilt x G5684-R-8 Vertical Collet RackLubrication MaintenanceSchedule Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingFor proper use and safety Gibs To adjust the table gibsTo adjust the headstock gibs To adjust the X-axis leadscrew Battery ReplacementTo adjust the Y-axis leadscrew nut To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram 110 VACRear panel Side panelParts Column BreakdownColumn Parts List DescriptionElectrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. since 09/09 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY