Grizzly G0704 owner manual G5758-Tilt x, G5684-R-8 Vertical Collet Rack

Page 37

G9511—T-Slot Nuts, 4 PK, 7/16" Slot, 3/8"-16Heat treated steel T-Slot Nuts with black oxide finish feature an imperfect thread in the base of the T-nut to eliminate any danger of screwing the clamping stud through and damaging the table slot.

Figure 40. Model G9511 T-Slot Nuts.

G5758—Tilt Table 5" x 7"

Set your work at any angle with these sturdy tilt tables. Heavy-duty construction includes T-slots, two locking screws and precision base that allows the table to tilt from -45 Degrees to +45 Degrees. Table size: 5" x 7".

Figure 41. Model G5758 Tilt Table.

Model G0704 (Mfg. since 09/09)

G9849—Magnetic Base/Dial Indicator Combo Precision measurements and setups have never been so easy. Magnetic base engages with just the turn of a switch and allows pinpoint adjust- ment. The dial indicator features 0-1" travel and has a resolution of 0.001". This fine set includes a molded case for protection and convenience.

Figure 42. Model G9849 Indicator/Base Combo

G5684—R-8 Vertical Collet Rack

No more loose R-8 collets laying around in your tool box. Organize with this handy collet rack and you won’t be looking at each one for the correct size. Set on your bench or mount to a wall. Holds 48 collets.

Figure 43. Model G5684 Tilt Table.

-35-

Image 37

Contents Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification G0704 electronic controls identification Electronic Controls IdentificationMachine Data Sheet Other Features Safety Instructions for Machinery SafetyUnattended OPERATION. Never leave Additional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWGNeeded for Setup SetupUnpacking Description QtyInventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Weight LoadMoving & Placing Machine Example of a direct mount setupBolting to Concrete Floors Mounting to Shop FloorTo install the drill chuck onto the arbor AssemblyDrill Chuck Arbor To assemble your machineConnecting Power Power ConnectionTo test run and break-in the spindle bearings Test Run & Spindle Break-inBasic Controls OperationsSpeed Range Selector Knob Selects low range Digital readout unit controls Operation Overview To use the digital readout Digital Readout UnitTo determine the needed spindle speed Calculating Spindle SpeedTo set the spindle speed Spindle Speed DirectionSpindle Height Controls Changing Spindle Position Using Quill Feed LeversDrill Chuck To install the drill chuck and arborLoading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8179 AccessoriesH8177-Worktable with Angle G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table G5684-R-8 Vertical Collet Rack G5758-Tilt xSchedule MaintenanceLubrication To lubricate the leadscrews Tools Needed QtyHandwheel gears Troubleshooting ServiceFor proper use and safety To adjust the headstock gibs To adjust the table gibsGibs To adjust the Y-axis leadscrew nut Battery ReplacementTo adjust the X-axis leadscrew To replace the digital readout unit batteryTo inspect and replace the motor brushes Motor ServiceWiring Safety Instructions Wiring110 VAC Wiring DiagramSide panel Rear panelColumn Breakdown PartsDescription Column Parts ListElectrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. since 09/09 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY