Grizzly G0704 owner manual Inventory, Contents Qty, Not Shown

Page 16

Inventory

The following is a description of the main compo- nents shipped with your machine. Lay the compo- nents out to inventory them.

If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

Contents		Qty
A.	Mill/Drill w/Stand	1
B.	Open End Combo Wrench 17/19	1
C.	Open End Combo Wrench 8/10	1
D.	Bottle for Oil	1
E.	Tool Box	1
F.	Large Handwheel Handle	1
G.	Small Handwheel Handles	3
H.	T-Bolts M10-1.5 x 60 (vise mounting)	2
	Flat Washers 10mm (vise mounting)	2
	Hex Nuts M10-1.5 (vise mounting)	2
I.	Drill Chuck	1
J.	Chuck Key	1
K.	Phillips Screwdriver	1
L.	Flat Screwdriver	1
M.	Arbor B16 x R8	1
N.	Hex Wrench Set 2, 3, 4, 5, & 6mm	1 ea.
Not Shown:
	Hex Bolts M10-1.5 x 50	4
	Flat Washers 10mm	4

-14-

A

Figure 4. G0704 out of the crate.

NOTICE

If you cannot find an item on this list, check the mounting location on the machine or the packaging materials. Sometimes parts are pre-installed for shipping, or they become hidden by packaging materials.

Model G0704 (Mfg. since 09/09)

Image 16

Contents Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification Electronic Controls Identification G0704 electronic controls identificationMachine Data Sheet Other Features Safety Safety Instructions for MachineryUnattended OPERATION. Never leave Additional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftSetup Needed for SetupUnpacking Description QtyInventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsAssembly To install the drill chuck onto the arborDrill Chuck Arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsBasic Controls OperationsSpeed Range Selector Knob Selects low range Digital readout unit controls Operation Overview Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckLoading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8179 AccessoriesH8177-Worktable with Angle G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table G5758-Tilt x G5684-R-8 Vertical Collet RackSchedule MaintenanceLubrication Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingFor proper use and safety To adjust the headstock gibs To adjust the table gibsGibs Battery Replacement To adjust the Y-axis leadscrew nutTo adjust the X-axis leadscrew To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram 110 VACRear panel Side panelParts Column BreakdownColumn Parts List DescriptionElectrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. since 09/09 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY