Grizzly G0704 owner manual Machine Data Sheet

Page 7

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0704 DRILL/MILL WITH STAND

Product Dimensions:
Weight	265 lbs.
Width (side-to-side) x Depth (front-to-back) x Height	38 x 24 x 31 in.
Footprint (Length x Width)	13-3/8 x 16-1/2 in.
Shipping Dimensions:
Carton #1
Type	Plywood
Content	Machine
Weight	309 lbs.
Length x Width x Height	28 x 30 x 35 in.
Carton #2
Type	Cardboard
Content	Stand
Weight	77 lbs.
Length x Width x Height	18 x 15 x 33 in.
Electrical:
Power Requirement	110V, Single-Phase, 60 Hz
Minimum Circuit Size	15 Amp
Switch	ON/OFF Buttons with Lockout Cover
Switch Voltage	110V
Cord Length	6 ft.
Cord Gauge	18 gauge
Plug Included	Yes
Included Plug Type	NEMA 5-15
Motors:
Main
Type	Universal
Horsepower	1 HP
Voltage	110V
Phase	Single-Phase
Amps	3.2A
Speed	5000 RPM
Cycle	60 Hz
Number of Speeds	1
Power Transfer	Gear Drive
Bearings	Shielded and Permanently Sealed

Model G0704 (Mfg. since 09/09)

-5-

Image 7

Contents Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification G0704 electronic controls identification Electronic Controls IdentificationMachine Data Sheet Other Features Safety Instructions for Machinery SafetyUnattended OPERATION. Never leave Additional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWGDescription Qty SetupNeeded for Setup UnpackingInventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Weight LoadMoving & Placing Machine Example of a direct mount setupBolting to Concrete Floors Mounting to Shop FloorTo assemble your machine AssemblyTo install the drill chuck onto the arbor Drill Chuck ArborConnecting Power Power ConnectionTo test run and break-in the spindle bearings Test Run & Spindle Break-inBasic Controls OperationsSpeed Range Selector Knob Selects low range Digital readout unit controls Operation Overview To use the digital readout Digital Readout UnitTo determine the needed spindle speed Calculating Spindle SpeedTo set the spindle speed Spindle Speed DirectionSpindle Height Controls Changing Spindle Position Using Quill Feed LeversDrill Chuck To install the drill chuck and arborLoading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8179 AccessoriesH8177-Worktable with Angle G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table G5684-R-8 Vertical Collet Rack G5758-Tilt xSchedule MaintenanceLubrication To lubricate the leadscrews Tools Needed QtyHandwheel gears Troubleshooting ServiceFor proper use and safety To adjust the headstock gibs To adjust the table gibsGibs To replace the digital readout unit battery Battery ReplacementTo adjust the Y-axis leadscrew nut To adjust the X-axis leadscrewTo inspect and replace the motor brushes Motor ServiceWiring Safety Instructions Wiring110 VAC Wiring DiagramSide panel Rear panelColumn Breakdown PartsDescription Column Parts ListElectrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. since 09/09 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY