Grizzly G0517g instruction manual About Service, Troubleshooting, Motor & Electrical

Page 28

SECTION 7: SERVICE

About Service

This section is provided for your convenience—it is not a substitute for the Grizzly Service Department. If you need help troubleshooting, you need replacement parts, or you are unsure of how to perform the pro- cedures in this section, then feel free to call our Technical Support at (570) 546-9663.

Troubleshooting

Motor & Electrical

Symptom	Possible Cause	Possible Solution
Machine does not start or a	1. Plug or receptacle is at fault or wired	1. Test power plug and receptacle for good contact and
breaker trips.	incorrectly.	correct wiring.
	2. Cable or wiring is open or has high	2. Troubleshoot wires for internal or external breaks,
	resistance.	check for disconnected or corroded connections and
		repair or replace wiring, as necessary.
	3. Power supply is faulty, or is switched	3. Make sure all hot lines and grounds are operational
	OFF.	and have correct voltage on all legs.
	4. Safety switch key is at fault.	4. Install or replace safety key, or replace switch assem-
		bly.
	5. ON/OFF switch at fault.	5. Replace faulty switch.
	6. Motor connection is wired incorrectly.	6. Correct motor wiring (see Page 28).
	7. Motor is at fault.	7. Test, repair or replace motor.

Machine stalls or is under-	1. Incorrect spindle speed or feed rate.	1. Decrease spindle speed or feed rate.
powered.	2. Machine is undersized for the task.	2. Use smaller drill bits/cutters and reduce the feed rate
		and spindle speed.
	3. Bit or cutter is too large for machine.	3. Use a smaller bit.
	4. Belts are slipping.	4. Replace bad belts, align pulleys, and re-tension.
	5. Plug or receptacle is at fault.	5. Test power plug and receptacle for good contact and
		correct wiring.
	6. Pulley is slipping on shaft.	6. Replace loose pulley and shaft.
	7. Low power supply voltage.	7. Make sure hot lines and grounds are operational w/
		correct voltage.
	8. Motor bearings are at fault.	8. Rotate motor shaft for noisy or burnt bearings, repair/
		replace as required.
	9. Motor has overheated.	9. Clean dust off motor, let it cool, and reduce workload
		on machine.
	10.Motor connection is wired incorrect-	10.Correct motor wiring (see Page 28).
	ly.
	11. Motor is at fault.	11.Test, repair or replace motor.

-26-	Model G0517 Mill/Drill

Image 28

Contents Model G0517 MILL/DRILL Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet Model G0517 Mill/Drill Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Mill/Drills Circuit Requirements OperationSET UP Items Needed for Set UpUnpacking InventoryClean Up Site ConsiderationsFloor Load Minimum Working ClearancesAssembly To assemble the mill/drillPage Test Run To test run the machineHead/Quill Travel OperationsTable Travel To install a sleeve Installing/Removing Morse Taper SleevesTo remove a sleeve To install the drawbar with attached tooling Installing/Removing Drawbar ToolingTo remove the drawbar and tooling Installing Drill Chuck To install the drill chuckChanging Speeds To change speedsDrilling Drilling Speeds Using the Drill Bit Speed ChartLubrication Suggestions Milling Speed To determine the needed speed for millingCutting Speeds for High Speed Steel HSS Cutting Tools ExampleG3640-Power Twist V-Belt 1⁄2 x AccessoriesH5685-4Rotary Table H3022-Measurement Tool Set G9765-9-PC. Ball End Mill SetG1076-52-PC. Clamping Kit Maintenance ScheduleUnpainted Cast Iron LubricationTo adjust the gibs Adjusting GibsOil Fittings Service About ServiceTroubleshooting Symptom Possible Cause Possible SolutionMill/Drill Operations Wiring Diagram Electrical ComponentsStand/Base Parts Breakdown Stand/Base Parts List DescriptionHeadstock Parts Breakdown Headstock Parts List DescriptionWarranty and Returns Page Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog