Bostitch FN1664 manual Fittings, Hoses, Supply Source, Regulator, Operating Pressure, Filter

Page 6

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

FITTINGS:

Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source.

HOSES:

Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system. The supply hose should contain a fitting that will provide “quick disconnecting” from the male plug on the tool.

SUPPLY SOURCE:

Use only clean regulated compressed air as a power sourcefor this tool. NEVER USE OXYGEN, COMBUSTIBLE GASES, OR BOTTLED GASES,AS A POWER SOURCE FOR THIS TOOL AS TOOL MAYEXPLODE.

REGULATOR:

A pressure regulator with an operating pressure of 0 - 125 p.s.i. (0 - 8.79 kg/cm2) is required to control the operating pressure for safe operation of this tool. Do not connect this tool to air pressure which can potentially exceed 200 p.s.i. (14 kg/cm2) as tool may fracture or burst, possibly causing injury.

OPERATING PRESSURE:

Do not exceed recommended maximum operating pressure as tool wear will be greatly increased. The air supply must be capable of maintaining the operating pressure at the tool. Pressure drops in the air supply can reduce the tool’s driving power. Refer to “TOOL SPECIFICATIONS” for setting the correct operating pressure for the tool.

FILTER:

Dirt and water in the air supply are major causes of wear in pneumatic tools. A filter will help to get the best performance and minimum wear from the tool. The filter must have adequate flow capacity for the specific installation. The filter has to be kept clean to be effective in providing clean compressed air to the tool. Consult the manufacturer’s instructions on proper maintenance of your filter. A dirty and clogged filter will cause a pressure drop which will reduce the tool’s performance.

Quick Connect Plug

Quick Disconnect Plug

-6-

Image 6
Contents FN1664 Introduction IndexLoadingtool Safety InstructionsAIR Supply and Connections OperationTool Components Tool Specifications Fastener SpecificationsSupply Source FittingsHoses RegulatorLoadingthe FN1664 To Prevent Accidental InjuriesTrigger Lockout Control Trip Operation ModeSelecting the Trip Mode ContacttripDIAL-A-DEPTH Fastener Control Adjustment BOSTITCH, INCInstalling the Belt Hook Usingthe Integrated Pencil SharpenerHEX Wrench Storage Contact Trip Operation Tool OperationBefore Handling or Operating this Tool Sequentialtrip OperationJAM Clearing Procedure Tool Operation Check Maintainingthe PneumatictoolMaintenance Checklist Maintenance Benefit Procedure Service IntervalTrouble Shooting ProblemCausecorrection Availableaccessories Bostitch Finish &TRIM Products Introducción ÍndiceNota Carga DE LA Herramienta Instrucciones DE SeguridadSuministro DE Airey Conexiones FuncionamientoComponentes DE LA Herramienta Especificaciones DE LA Herramienta Especificaciones DE FijacionesFuente DE Suministro ConectoresMangueras ReguladorCarga DE LA FN1664 Para Prevenir Lesiones AccidentalesDisparo DE Contacto Control DE Bloqueo DEL GatilloModo DE Funcionamiento DEL Disparador Disparo SecuencialAjuste DE Control DE Fijaciones DIAL-A-DEPTH Instalación DEL Gancho Para EL Cinturón USO DEL Sacapuntas IntegradoAlmacenamiento DE LA Llave Hexagonal Funcionamiento DEL Disparo DE Contacto Funcionamiento DE LA HerramientaAntes DE Manipular U Operar Esta Herramienta Funcionamiento DEL Disparo SecuencialProcedimiento Para Despejar Atascos Mantenimiento DE LA Herramienta Neumática Presión Y Volumen DEL Suministro DE AireRevisión Funcional DE LA Herramienta Piezas DE RepuestoLista DE Verificación DE Mantenimiento Mantenimiento Beneficio Procedimiento Intervalo De servicioSolución DE Problemas Problema Causa CorrecciónAccesorios Disponibles Productos Bostitch Para Rematey Detalle Remarque Garantie Limitée É.-U. et Canada seulementChargement DE L’OUTIL Consignes DE SécuritéAlimentation Dair ET Connexions FonctionnementComposants DE Loutil Spécifications DE L’OUTIL Caractéristiques DES AttachesSource D’ALIMENTATION RaccordsTuyauxsouples RégulateurChargement DE LA FN1664 Afin DE Prévenir LES Blessures AccidentellesControl DE Bloqueo DEL Gatillo Ajustement DE LA Commande D’ATTACHE DIAL-A-DEPTH Installation DU Crochet DE Ceinture Pour Utiliser LETAILLE-CRAYONINTÉGRÉRangement DE LA CLÉ HEX Fonctionnement EN Mode Déclenchement SUR Contact Fonctionnement EN Mode Déclenchement SéquentielFonctionnement DE L’OUTIL Procédure Pour LE Dégagement DES Blocages Entretien DE L’OUTIL Pneumatique Alimentation DAIR-PRESSION ET VolumeVérification DU Fonctionnement DE L’OUTIL Pièces DE RechangeEntretien Bienfait Procédure Intervalle De service Liste DE Vérification Pour L’ENTRETIENCausesolution DépannageProblème Accessoires Disponibles Produits DE Finition ET D’HABILLAGE Bostitch