Hobart Welding Products 210 MVP manual Changing Drive Roll Or Wire Inlet Guide, 023/.025, Stamped

Page 34

7-4. Changing Drive Roll Or Wire Inlet Guide

! Turn off welding power source.

Tools Needed:

2

4

3

1

1Inlet Wire Guide Securing Screw

2Inlet Wire Guide

Loosen screw. Slide tip as close to drive rolls as possible without touching. Tighten screw.

3 Retaining Pin

To remove drive roll, push drive roll in and rotate it (1/4 turn) to the open slot and slide it out over the retaining pin.

To secure drive roll, locate open slot and push drive roll completely over retaining pin, then rotate drive roll (1/4 turn) to closed slot.

4 Drive Roll

The drive roll consists of two different sized grooves. The stamped markings on the end

 

 

.030/.035

.023/.025

.030/.035

.030/.035

V Groove

V Groove

Knurled

 

 

Smooth

 

 

Groove

 

 

Groove

 

 

 

 

 

 

 

 

Stamped

Stamped

Stamped

Stamped

.030..035

.030..035 VK

.030..035

.024

 

surface of the drive roll refers to the groove on the opposite side of the drive roll. The groove closest to the motor shaft is the proper groove to thread (see Section 5-16).

250 763-A

OM-249 498 Page 30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Description OM-249 498BProcesses File MIG GmawFrom Hobart to You Protect Your InvestmentTable of Contents Warranty Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can burnWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Equipment can injure Welding Wire can injureFire or Explosion hazard Moving Parts can injureEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion Risque D’INCENDIE OU LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LE Soudage À L’ARC risque de provoquer des interférencesInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-249 498 I1max Symbols And Definitions− Definitions I1effSpecifications For 230 VAC − SpecificationsSpecifications For 115 VAC 20% duty cycle at 90 amps Minutes Welding Duty Cycle And Overheating30% duty cycle at 150 amps Minutes Welding OverheatingVolt-Ampere Curves Voltage AmperageInstalling Nozzle, Contact Tip, And Adapter − InstallationInstalling Welding Gun Installing Work Clamp Process/Polarity Table Turn off welding power sourceChanging Polarity After flow is set, close pressure assembly Installing Gas SupplyTools Needed 1-1/8 Electrical Service Guide Extension Cord Data Use Shortest Cord PossibleMulti−Voltage Plug MVP Connection Do Not modify or rewire receptacle Connection Selecting a Location And Connecting Input PowerDo not move or operate Unit where it could tip Serial Number And Rating Label LocationQualified Persons Make InstallationLocal Codes − have only YellowConnecting 1-Phase Input Power For 115 VAC Input Installing Wire Spool And Adjusting Hub Tension Installing 8 in mm Wire SpoolWire Feed Speed Control Connecting Optional Spool GunExposed O-rings Threading Welding Wire − Operation ControlsWeld Parameter Chart Overload Protection − Maintenance &TROUBLESHOOTINGRoutine Maintenance Drive Motor Protection030/.035 Groove Knurled Smooth Changing Drive Roll Or Wire Inlet Guide023/.025 StampedRemove nozzle, contact tip, and adapter Blow out gun casing Nozzle Contact Tip Tip Adapter Head TubeStickout Tools Needed Mm, 10 mm Replacing Switch And/Or Head Tube Troubleshooting Table Trouble Remedy− Electrical Diagram Circuit Diagram249 315-A Typical MIG Process Connections Regulator Flowmeter Shielding Gas Wire Feeder Power Source− MIG Welding Gmaw Guidelines Gun Workpiece Work ClampWire Size Amperage Range Typical MIG Process Control SettingsSelect Voltage Holding And Positioning Welding Gun Groove WeldsPerpendicular Drag Conditions That Affect Weld Bead ShapePush Short Normal LongGood Weld Bead Characteristics Poor Weld Bead CharacteristicsGun Movement During Welding Troubleshooting − Excessive Penetration Troubleshooting − Excessive SpatterTroubleshooting − Porosity Possible Causes Corrective ActionsTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Burn-Through Base metal to move Troubleshooting − Waviness Of BeadTroubleshooting − Distortion DirectionCommon MIG Shielding Gases Troubleshooting Guide For Semiautomatic Welding EquipmentApplication Welding power source Welding arc not stable Wire slipping in drive rollsReadjust welding parameters Drive rolls if necessary57 58 − Parts List49 32 Dia Part Description Quantity Optional H100S4-10 Gun 245Options Optional Drive RollsConsumables Support ServiceAssistance Contact your Distributor for Hobart Welding Products
Top Page Image Contents