Hobart Welding Products 210 MVP California Proposition 65 Warnings, Principal Safety Standards

Page 8

1-4. California Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm. Wash hands after use.

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www.global.ihs.com).

Safe Practices for the Preparation of Containers and Piping for Welding and Cutting, American Welding Society Standard AWS F4.1, from Glob- al Engineering Documents (phone: 1-877-413-5184, website: www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 4221 Walney Road, 5th Floor, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 5060 Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone: 800-463-6727, website: www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec- tion, ANSI Standard Z87.1, from American National Standards Institute,

For Gasoline Engines:

Engine exhaust contains chemicals known to the State of California to cause cancer, birth defects, or other reproduc- tive harm.

For Diesel Engines:

Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, NFPA Standard 51B, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.

OSHA, Occupational Safety and Health Standards for General Indus- try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, from U.S. Government Printing Office, Super- intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954 (phone: 1-866-512-1800) (there are 10 OSHA Regional Offices— phone for Region 5, Chicago, is 312-353-2220, website: www.osha.gov).

U.S. Consumer Product Safety Commission (CPSC), 4330 East West Highway, Bethesda, MD 20814 (phone: 301-504-7923, website: www.cpsc.gov).

Applications Manual for the Revised NIOSH Lifting Equation, The Na- tional Institute for Occupational Safety and Health (NIOSH), 1600 Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website: www.cdc.gov/NIOSH).

1-6. EMF Information

Electric current flowing through any conductor causes localized electric and magnetic fields (EMF). Welding current creates an EMF field around the welding circuit and welding equipment. EMF fields may inter- fere with some medical implants, e.g. pacemakers. Protective measures for persons wearing medical implants have to be taken. For example, access restrictions for passers−by or individual risk assess- ment for welders. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

1.Keep cables close together by twisting or taping them, or using a cable cover.

2.Do not place your body between welding cables. Arrange cables to one side and away from the operator.

3.Do not coil or drape cables around your body.

4.Keep head and trunk as far away from the equipment in the welding circuit as possible.

5.Connect work clamp to workpiece as close to the weld as possible.

6.Do not work next to, sit or lean on the welding power source.

7.Do not weld whilst carrying the welding power source or wire feeder.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the device manufacturer before performing or going near arc welding, spot welding, gouging, plasma arc cutting, or induction heating operations. If cleared by your doctor, then following the above procedures is recom- mended.

OM-249 498 Page 4

Image 8
Contents OM-249 498B ProcessesDescription File MIG GmawFrom Hobart to You Protect Your InvestmentTable of Contents Warranty Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can burnFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can injure Fire or Explosion hazardFalling Equipment can injure Moving Parts can injurePrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un incendie ou une explosion LES Pièces Chaudes peuvent provoquer des brûluresLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresProposition californienne 65 Avertissements Les Pièces Mobiles peuvent causer des blessuresLES Fils DE Soudage peuvent provoquer des blessures LE Soudage À L’ARC risque de provoquer des interférencesEn ce qui concerne les implants médicaux Principales normes de sécuritéInformations relatives aux CEM OM-249 498 Symbols And Definitions − DefinitionsI1max I1effSpecifications For 115 VAC − SpecificationsSpecifications For 230 VAC Duty Cycle And Overheating 30% duty cycle at 150 amps Minutes Welding20% duty cycle at 90 amps Minutes Welding OverheatingVolt-Ampere Curves Voltage AmperageInstalling Welding Gun − InstallationInstalling Nozzle, Contact Tip, And Adapter Installing Work Clamp Changing Polarity Turn off welding power sourceProcess/Polarity Table Tools Needed 1-1/8 Installing Gas SupplyAfter flow is set, close pressure assembly Electrical Service Guide Extension Cord Data Use Shortest Cord PossibleMulti−Voltage Plug MVP Connection Selecting a Location And Connecting Input Power Do not move or operate Unit where it could tipDo Not modify or rewire receptacle Connection Serial Number And Rating Label LocationInstallation Local Codes − have onlyQualified Persons Make YellowConnecting 1-Phase Input Power For 115 VAC Input Installing Wire Spool And Adjusting Hub Tension Installing 8 in mm Wire SpoolExposed O-rings Connecting Optional Spool GunWire Feed Speed Control Threading Welding Wire − Operation ControlsWeld Parameter Chart − Maintenance &TROUBLESHOOTING Routine MaintenanceOverload Protection Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide 023/.025030/.035 Groove Knurled Smooth StampedStickout Tools Needed Mm, 10 mm Nozzle Contact Tip Tip Adapter Head TubeRemove nozzle, contact tip, and adapter Blow out gun casing Replacing Switch And/Or Head Tube Troubleshooting Table Trouble Remedy− Electrical Diagram Circuit Diagram249 315-A Regulator Flowmeter Shielding Gas Wire Feeder Power Source − MIG Welding Gmaw GuidelinesTypical MIG Process Connections Gun Workpiece Work ClampSelect Voltage Typical MIG Process Control SettingsWire Size Amperage Range Holding And Positioning Welding Gun Groove WeldsConditions That Affect Weld Bead Shape PushPerpendicular Drag Short Normal LongGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Troubleshooting − Excessive Spatter Troubleshooting − PorosityTroubleshooting − Excessive Penetration Possible Causes Corrective ActionsTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Waviness Of Bead Troubleshooting − DistortionBase metal to move DirectionApplication Troubleshooting Guide For Semiautomatic Welding EquipmentCommon MIG Shielding Gases Welding arc not stable Wire slipping in drive rolls Readjust welding parametersWelding power source Drive rolls if necessary49 32 − Parts List57 58 Dia Part Description Quantity Optional H100S4-10 Gun 245Consumables Optional Drive RollsOptions Assistance ServiceSupport Contact your Distributor for Hobart Welding Products