Grizzly Model G0638 owner manual Additional Safety for Dust Collectors

Page 12

Additional Safety for Dust Collectors

1.MACHINE USE. Do not use this dust collec- tor to pick up liquids and metal scraps, includ- ing, but not limited to, nails and filings. Also, do not pick up material which cannot safely pass through the impeller such as solid wood scraps.

2.KEEPING FINGERS SAFE. Do not place your hands or tools near the open inlet during operation. The moving impeller could cause serious damage to body parts if touched while spinning.

3.SAFE SERVICING. Disconnect power and allow the impeller to come to a complete stop before servicing or working on the dust col- lector ducting system.

4.SUSPENDED DUST PARTICLES AND IGNI- TION SOURCES. Do not operate the dust collector in areas where explosion risks would be high if dust were dispersed into the area. Areas of high risk include, but are not lim- ited to, areas near pilot lights and/or open flames.

5.DUST HAZARD. Be aware that certain woods may cause an allergic reaction in people and animals, especially when exposed to fine dust. Make sure you know what type of wood dust you will be exposed to in case of an allergic reaction. Always wear an approved respirator during and for a short time after machine operation!

6.AVOIDING FIRES. Do not allow steel to strike against impeller—this may produce a spark. Sparks can smolder in wood dust for a long time before fire or flame is detected. If metal contacts metal during operation, immediately turn off the dust collector, flip the disconnect switch and wait for all mov- ing parts to stop. Remove collection bags and empty the dust into an approved air tight metal container in case of spark. Remedy the metal to metal contact problem before resuming operation.

7.OPERATIONAL QUESTIONS. If at any time you are experiencing difficulties perform- ing the intended operation, stop using the machine! Then contact our Tech Support or ask a qualified expert how the operation should be performed.

8.CLEANING AIR. Do not confuse this dust collector with an air cleaner. This dust col- lector is only designed to collect dust from a machine, not clean dust suspended in the air.

9.EMPTYING DUST. When emptying dust from the collection bags or drum, wear a respirator and safety glasses. Empty dust into an approved container and dispose of properly.

Like all machines there is danger associ- ated with this dust collector. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the pos- sibility of operator injury. If normal safety precautions are overlooked or ignored, seri- ous personal injury may occur.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results.

-10-

G0637/G0638 Cyclone Dust Collector

Image 12
Contents 71/2 & 10 HP Cyclone Dust Collectors Model G0637Page Table of Contents Introduction ForewordContact Info G0637 Machine Data Sheet G0637 Data Sheet G0637/G0638 Cyclone Dust Collector G0638 Machine Data Sheet G0638 Data Sheet G0637/G0638 Cyclone Dust Collector Identification G0637/G0638 Cyclone Dust Collector G0637/G0638 Cyclone Dust Collector Additional Safety for Dust Collectors Phase Converter Connection to PowerCircuit Requirements Full Load Amperage DrawModel G0637 440V Conversion Model G0638 440V ConversionTo convert the G0638 to Setup Setup SafetyItems Needed for Setup UnpackingInventory Inventory Figures QtyInventory Qty Placement Location Site ConsiderationsFloor Load LightingClean Up Mounting to Shop FloorBolting to Concrete Floors Hardware Identification Chart Assembly Upper StandIntake Cylinder and Blower Housing Intake Barrel and Large Cyclone FunnelBlower Housing and Intake Barrel Assemblies Cyclone mounting bracket mounted To collector assemblySecuring intake barrel assembly to Blower housing assembly Outlet Port and Canister Filters Canister filter collection bag installed Small Cyclone Funnel and Funnel Port Dust Collection Drum AssembliesPage Model G0637 Control Box Model G0638 Control BoxTest Run To test run your dust collection systemFor the G0638 only Designing System GeneralDuct Material Metal DuctFlexible Duct Plastic DuctSystem Design Decide Who Will DesignSketch Your Shop Layout Sketch a Basic Duct LayoutDetermine Required CFM of Each Machine Machine ApproximateMachine Determining Main Line Duct Size Determining Branch Line Duct SizeTotal CFM Branch Line Size Calculating Duct Resistance System Grounding Blast Gate Accessories Metal Duct Starter KitMetal Elbows Metal BranchesReducers & Adapters G6252-4 Floor Sweep G7341-5 Floor Sweep G7342-6 Floor SweepDust collection pipe clamps H2443-Universal AdapterOperation Safety Remote ControlOperations Maintenance Cleaning FiltersSchedule Emptying DrumsService TroubleshootingMotor & Electrical Symptom Possible Cause Possible Solution Dust Collector OperationService Log Date Approximate Hours Of Use Service PerformedG0637 Electrical Components Model G0637 control boxWiring Diagrams Pages 44 G0638 Electrical Components Model G0638 control boxPages 47 Pages 47 Parts Breakdown Parts List DescriptionCollection Drum LID Label Placement Warranty and Returns Page Page