Grizzly Model G0638 Small Cyclone Funnel and Funnel Port, Dust Collection Drum Assemblies

Page 26

Small Cyclone Funnel and Funnel Port

1.Apply the 3 x 6 x 2200mm gasket to the larg- er, top end of the small cyclone funnel, then place the cyclone funnel upside down on the floor.

Note: Use a clean covering on the floor to protect the gasket.

2.Apply the 3 x 6 x 735mm gasket to the top of the funnel port and place this upside down on top of the cyclone funnel.

3.Attach the small cyclone funnel and funnel port with (6) 516"-18 x 114" hex bolts, (12) 516" flat washers, and (6) 516"-18 hex nuts.

4.With assistance, attach this assembly to the bottom of the large cyclone funnel with (9) 516"-18 x 114" hex bolts, (18) 516" flat washers, and (9) 516"-18 hex nuts (see Figure 31).

Small

Cyclone

Funnel

Funnel

Port

Figure 31. Small cyclone funnel and funnel port

attached.

-24-

Dust Collection Drum Assemblies

1.For each lower collection drum cylinders, attach the casters to the bottom using (4) 38"- 16 hex nuts, (4) 38" flat washers, and (4) 38" lock washers (see Figure 32).

Figure 32. Dust collection drum casters installed.

2.Connect each upper and lower collection drum cylinder with a collection drum clamp and use (1) 516"-18 x 3" hex bolt and (1) 516"- 18 hex nut to tighten the clamp (see Figure 33).

Figure 33. Installing drum clamp around dust

collection cylinders.

G0637/G0638 Cyclone Dust Collector

Image 26
Contents 71/2 & 10 HP Cyclone Dust Collectors Model G0637Page Table of Contents Contact Info IntroductionForeword G0637 Machine Data Sheet G0637 Data Sheet G0637/G0638 Cyclone Dust Collector G0638 Machine Data Sheet G0638 Data Sheet G0637/G0638 Cyclone Dust Collector Identification G0637/G0638 Cyclone Dust Collector G0637/G0638 Cyclone Dust Collector Additional Safety for Dust Collectors Circuit Requirements Phase ConverterConnection to Power Full Load Amperage DrawTo convert the G0638 to Model G0637 440V ConversionModel G0638 440V Conversion Items Needed for Setup SetupSetup Safety UnpackingInventory Qty InventoryInventory Figures Qty Floor Load Placement LocationSite Considerations LightingBolting to Concrete Floors Clean UpMounting to Shop Floor Hardware Identification Chart Assembly Upper StandIntake Cylinder and Blower Housing Intake Barrel and Large Cyclone FunnelBlower Housing and Intake Barrel Assemblies Cyclone mounting bracket mounted To collector assemblySecuring intake barrel assembly to Blower housing assembly Outlet Port and Canister Filters Canister filter collection bag installed Small Cyclone Funnel and Funnel Port Dust Collection Drum AssembliesPage Model G0637 Control Box Model G0638 Control BoxFor the G0638 only Test RunTo test run your dust collection system Duct Material Designing SystemGeneral Metal DuctFlexible Duct Plastic DuctSketch Your Shop Layout System DesignDecide Who Will Design Sketch a Basic Duct LayoutMachine Determine Required CFM of Each MachineMachine Approximate Total CFM Branch Line Size Determining Main Line Duct SizeDetermining Branch Line Duct Size Calculating Duct Resistance System Grounding Blast Gate Accessories Metal Duct Starter KitReducers & Adapters Metal ElbowsMetal Branches G6252-4 Floor Sweep G7341-5 Floor Sweep G7342-6 Floor SweepDust collection pipe clamps H2443-Universal AdapterOperations Operation SafetyRemote Control Schedule MaintenanceCleaning Filters Emptying DrumsMotor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible Solution Dust Collector OperationService Log Date Approximate Hours Of Use Service PerformedG0637 Electrical Components Model G0637 control boxWiring Diagrams Pages 44 G0638 Electrical Components Model G0638 control boxPages 47 Pages 47 Parts Breakdown Parts List DescriptionCollection Drum LID Label Placement Warranty and Returns Page Page