Grizzly Model G0638 owner manual Outlet Port and Canister Filters

Page 24

6.To allow the mounting holes of the lower stand legs to align properly, slightly loosen the 16 fasteners that connect the lower stand braces to the upper stand legs (see Figure 24).

Lower Stand Brace Fasteners

Outlet Port and Canister Filters

1.Apply the 3 x 6 x 1100mm gasket to the square side of the outlet port.

2.Mount the outlet port to the blower hous- ing with (4) 5⁄16"-18 x 1" hex bolts, (8) 5⁄16" flat washers, and (4) 5⁄16"-18 hex nuts (see Figure 25).

Outlet

Port

Lower

Stand

Legs

Figure 24. Lower stand legs attached to the

upper stand assembly.

Mounting Hex Bolts

Filter

L-Braces

7.Secure the lower stand legs to the upper stand assembly with (24) 3⁄8"-16 x 3⁄4" hex bolts, (48) 3⁄8" flat washers, and (24) 3⁄8"-16 lock nuts.

8.Re-tighten the 16 fasteners connecting the lower stand braces to the assembly.

9.Remove the power lifting equipment from the assembly.

Note: The only other use for the power lift- ing equipment is moving the dust collection system into its permanent position when the assembly is complete.

-22-

Figure 25. Filter L-braces mounted to blower

housing.

3.Attach the filter L-braces to either side of the outlet port on the blower housing with (6) 5⁄16"- 18 x 1" hex bolts, (12) 5⁄16" flat washers, and

(6)5⁄16"-18 hex nuts.

4.Secure the short filter brace support to the back of the filter L-braces with (2) 3⁄8"-16 x 3⁄4" hex bolts, (4) 3⁄8" flat washers, and (2) 3⁄8"-16 hex nuts (see Figure 26).

Short

Brace

Support

Figure 26. Short filter brace support attached.

G0637/G0638 Cyclone Dust Collector

Page 23 Page 25
Image 24
Page 23 Page 25
Contents 71/2 & 10 HP Cyclone Dust Collectors Model G0637Page Table of Contents Introduction ForewordContact Info G0637 Machine Data Sheet G0637 Data Sheet G0637/G0638 Cyclone Dust Collector G0638 Machine Data Sheet G0638 Data Sheet G0637/G0638 Cyclone Dust Collector Identification G0637/G0638 Cyclone Dust Collector G0637/G0638 Cyclone Dust Collector Additional Safety for Dust Collectors Phase Converter Connection to PowerCircuit Requirements Full Load Amperage DrawModel G0637 440V Conversion Model G0638 440V ConversionTo convert the G0638 to Setup Setup SafetyItems Needed for Setup UnpackingInventory Inventory Figures QtyInventory Qty Placement Location Site ConsiderationsFloor Load LightingClean Up Mounting to Shop FloorBolting to Concrete Floors Hardware Identification Chart Assembly Upper StandIntake Cylinder and Blower Housing Intake Barrel and Large Cyclone FunnelBlower Housing and Intake Barrel Assemblies Cyclone mounting bracket mounted To collector assemblySecuring intake barrel assembly to Blower housing assembly Outlet Port and Canister Filters Canister filter collection bag installed Small Cyclone Funnel and Funnel Port Dust Collection Drum AssembliesPage Model G0637 Control Box Model G0638 Control BoxTest Run To test run your dust collection systemFor the G0638 only Designing System GeneralDuct Material Metal DuctFlexible Duct Plastic DuctSystem Design Decide Who Will DesignSketch Your Shop Layout Sketch a Basic Duct LayoutDetermine Required CFM of Each Machine Machine ApproximateMachine Determining Main Line Duct Size Determining Branch Line Duct SizeTotal CFM Branch Line Size Calculating Duct Resistance System Grounding Blast Gate Accessories Metal Duct Starter KitMetal Elbows Metal BranchesReducers & Adapters G6252-4 Floor Sweep G7341-5 Floor Sweep G7342-6 Floor SweepDust collection pipe clamps H2443-Universal AdapterOperation Safety Remote ControlOperations Maintenance Cleaning FiltersSchedule Emptying DrumsService TroubleshootingMotor & Electrical Symptom Possible Cause Possible Solution Dust Collector OperationService Log Date Approximate Hours Of Use Service PerformedG0637 Electrical Components Model G0637 control boxWiring Diagrams Pages 44 G0638 Electrical Components Model G0638 control boxPages 47 Pages 47 Parts Breakdown Parts List DescriptionCollection Drum LID Label Placement Warranty and Returns Page Page
Top Page Image Contents