Grizzly Model G0638 owner manual Assembly, Upper Stand

Page 20

Assembly

Upper Stand

1.Use (8) 38"-16 x 34" hex bolts, (16) 38" flat washers, and (8) 38"-16 lock nuts to connect 2 upper stand legs, 1 upper stand brace, and 1 lower stand brace only finger tighten the fasteners (see Figure 12).

Note: To make the installation of the fasten- ers easier, use scrap wood to raise the metal components off the floor.

Upper Stand Legs

Upper Stand Brace

Lower Stand Brace

Figure 12. One side of upper stand assembled.

2.Repeat Step 1 to make the other side of the upper stand.

Note: The 516" fender washers with a larger outside diameter will be used to attach the canister filters in later steps—do not use them for any other assembly.

3.Use (16) 38"-16 x 34" hex bolts, (32) 38" flat washer, and (16) 38"-16 lock nuts to con- nect the two sides of the upper stand with two upper stand braces and two lower stand braces—only finger tighten the fasteners (see Figure 13).

Figure 13. Upper stand assembled.

4.Place the level across a corner of the lower stand braces and move the upper stand around until that corner is level, then fully tighten all of the fasteners for that corner (see Figure 14).

Figure 14. Level positioned on the upper stand.

5.Repeat Step 4 for the rest of the corners, then set the upper stand assembly aside.

-18-

G0637/G0638 Cyclone Dust Collector

Image 20
Contents 71/2 & 10 HP Cyclone Dust Collectors Model G0637Page Table of Contents Contact Info IntroductionForeword G0637 Machine Data Sheet G0637 Data Sheet G0637/G0638 Cyclone Dust Collector G0638 Machine Data Sheet G0638 Data Sheet G0637/G0638 Cyclone Dust Collector Identification G0637/G0638 Cyclone Dust Collector G0637/G0638 Cyclone Dust Collector Additional Safety for Dust Collectors Phase Converter Connection to PowerCircuit Requirements Full Load Amperage DrawTo convert the G0638 to Model G0637 440V ConversionModel G0638 440V Conversion Setup Setup SafetyItems Needed for Setup UnpackingInventory Qty InventoryInventory Figures Qty Placement Location Site ConsiderationsFloor Load LightingBolting to Concrete Floors Clean UpMounting to Shop Floor Hardware Identification Chart Assembly Upper StandIntake Cylinder and Blower Housing Intake Barrel and Large Cyclone FunnelBlower Housing and Intake Barrel Assemblies Cyclone mounting bracket mounted To collector assemblySecuring intake barrel assembly to Blower housing assembly Outlet Port and Canister Filters Canister filter collection bag installed Small Cyclone Funnel and Funnel Port Dust Collection Drum AssembliesPage Model G0637 Control Box Model G0638 Control BoxFor the G0638 only Test RunTo test run your dust collection system Designing System GeneralDuct Material Metal DuctFlexible Duct Plastic DuctSystem Design Decide Who Will DesignSketch Your Shop Layout Sketch a Basic Duct LayoutMachine Determine Required CFM of Each MachineMachine Approximate Total CFM Branch Line Size Determining Main Line Duct SizeDetermining Branch Line Duct Size Calculating Duct Resistance System Grounding Blast Gate Accessories Metal Duct Starter KitMetal Elbows Metal BranchesReducers & Adapters G6252-4 Floor Sweep G7341-5 Floor Sweep G7342-6 Floor SweepDust collection pipe clamps H2443-Universal AdapterOperations Operation SafetyRemote Control Maintenance Cleaning FiltersSchedule Emptying DrumsMotor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible Solution Dust Collector OperationService Log Date Approximate Hours Of Use Service PerformedG0637 Electrical Components Model G0637 control boxWiring Diagrams Pages 44 G0638 Electrical Components Model G0638 control boxPages 47 Pages 47 Parts Breakdown Parts List DescriptionCollection Drum LID Label Placement Warranty and Returns Page Page