Delta 36-978 instruction manual Blade Guard and Splitter Assembly and Alignment

Page 18

BLADE GUARD AND SPLITTER

ASSEMBLY AND ALIGNMENT

1.Fasten the rear splitter mounting bracket (A) Fig. 43, to the rear trunnion. Align the two holes in the rear splitter mounting bracket (shown at B) with the two holes in the trunnion. Place a ¼" Lock Washer onto a ¼ -20 x ¾" Hex Head Screw, place a ¼" Flat Washer onto the hex head screw, insert the hex head screw through the hole in the rear splitter mounting bracket and thread the hex head screw into the rear trunnion. Repeat this process for the remaining hole. Do not completely tighten the two screws (B) at this time.

2.Raise saw arbor to its highest position.

3.Remove screw and large washer (C) Fig. 44 from the inside splitter mounting bracket.

4.Using a straight edge, check to see if the top and bottom of the inside splitter bracket (D) Fig. 45 is aligned with the inner arbor flange (E), as shown.

5.If alignment is necessary, loosen the two screws

(F) Fig. 46, align bracket (D) with the arbor flange and tighten screws (F).

6.Loosely assemble large washer and screw (C) Fig. 46 to the inside splitter bracket. This screw and washer was removed in STEP 3.

18

B

 

 

A

 

 

X

Y

Z

Fig. 43

C

Fig. 44

D

E

Fig. 45

D

C

F

Fig. 46

Image 18
Contents Contractor’s Saw Model 36-979 Shown With Model 36-B30 Fence SystemTable of Contents Important Safety InstructionsSafety Guidelines Tool Warning LabelsGeneral Safety Rules Important Safety InstructionsAdditional Specific Safety Rules Some Materials are TOO HardPower Connections Motor SpecificationsGrounding Instructions Volt Single Phase Operation Extension CordsCarton Contents Functional DescriptionSheet Metal Extension Wings Extension WingsStand and Mobile Base Parts Cast Iron Extension WingsAssembly Tools Required AssemblyUnpacking and Cleaning Assembly Time EstimateShort and Long LEG Supports Mobile Base and Stand AssemblyFront and Side Panels Corner BracketsAS Shown in FIG Leveling Feet Attaching Foot Lever Assembly to BaseOpen END is Aligned AS Shown in Figs WheelsMobile Base and Stand Assembly to SAW Dust Chute and Back BraceMotor to Motor Mounting Plate Blade Tilting Raising HandwheelWrench Hook E FMotor and Motor Mounting Plate to SAW Motor PULLEY, Pulley GUARD, and Drive BeltTo the Arbor Pulley Connecting Motor Cord to Switch Assembly Removing Motor for TransportBlade Guard and Splitter Assembly and Alignment Assemble the blade guard and splitter assembly Model 36-978 only Model 36-979 onlyOperation ON/OFF SwitchLocking Switch in the OFF Position Starting and Stopping SAWRaising and Lowering Blade Disconnect Machine from Power SourceOverload Protection Tilting the BladeAssembling Miter Gauge Miter Gauge Operation and AdjustmentAdjusting Table Insert Table Insert a should Always be Level with the TableAligning Miter Slots to Blade Changing the SAW BladeQuick Operations Checklist Machine USEKEY Parts and Safety Features on Your SAW Back ViewBlade Guard and Splitter USE CROSS-CUTTINGBevel Crosscutting Never USE the Fence AS a CUT-OFF Gauge When CROSS-CUTTINGMitering Compound MiteringRipping Constructing a Push StickUsing Moulding Cutterhead Bevel RippingUsing Accessory Dado Head Fig. S15Using Auxiliary Wood Facing Fig. S18Troubleshooting Power Tool InstituteConstructing a Featherboard Push Stick Constructing a Push StickMaintenance Shelf MeasurementsService AccessoriesWarranty Delta Machinery
Related manuals
Manual 100 pages 12.32 Kb