Delta 36-978 instruction manual Assemble the blade guard and splitter assembly

Page 19

7.Assemble the blade guard and splitter assembly

(G) Fig. 47, between the large washer (C) and the splitter bracket and tighten screw (H) with wrench supplied. Slide splitter as far down as it will go.

8. Fasten the rear of the blade guard and splitter bracket

assembly (G) Fig. 48, to the rear splitter mounting

bracket. Align the hole (J) in the blade guard and

splitter bracket with the hole in the rear splitter

mounting bracket. Insert a 5/16-18 x 5/8" Carriage

Head Screw through the hole and place a 5/16" Flat

Washer on the screw and fasten with a 5/16-18 Hex

Nut, and tighten securely.

G

H

C

Fig. 47

L G

IMPORTANT: The splitter (G) Fig. 49, has a notch (L) cut in the top edge as shown. This feature will enable the blade guard to stay in the raised position to make blade changing easier. Raise the front of blade guard (M), until the rear edge of the blade guard slips into notch (L) of splitter (G); the blade guard will stay in this position. This feature only works when the table insert is removed.

9.With the blade guard (L) Fig. 50, in the raised position, attach the saw blade (K) on the arbor with the two arbor wrenches provided (No. 7 and 8, Fig. 1). For more instructions on changing blades, see “CHANGING THE SAW BLADE” section in this manual.

Fig. 48

M

L

Fig. 49

J

G

L

K

Fig. 50

19

Image 19
Contents Model 36-979 Shown With Model 36-B30 Fence System Contractor’s SawImportant Safety Instructions Table of ContentsTool Warning Labels Safety GuidelinesImportant Safety Instructions General Safety RulesSome Materials are TOO Hard Additional Specific Safety RulesMotor Specifications Power ConnectionsGrounding Instructions Extension Cords Volt Single Phase OperationFunctional Description Carton ContentsCast Iron Extension Wings Extension WingsStand and Mobile Base Parts Sheet Metal Extension WingsAssembly Time Estimate AssemblyUnpacking and Cleaning Assembly Tools RequiredCorner Brackets Mobile Base and Stand AssemblyFront and Side Panels Short and Long LEG SupportsWheels Attaching Foot Lever Assembly to BaseOpen END is Aligned AS Shown in Figs AS Shown in FIG Leveling FeetDust Chute and Back Brace Mobile Base and Stand Assembly to SAWE F Blade Tilting Raising HandwheelWrench Hook Motor to Motor Mounting PlateMotor PULLEY, Pulley GUARD, and Drive Belt Motor and Motor Mounting Plate to SAWTo the Arbor Pulley Removing Motor for Transport Connecting Motor Cord to Switch AssemblyBlade Guard and Splitter Assembly and Alignment Assemble the blade guard and splitter assembly Model 36-979 only Model 36-978 onlyStarting and Stopping SAW ON/OFF SwitchLocking Switch in the OFF Position OperationTilting the Blade Disconnect Machine from Power SourceOverload Protection Raising and Lowering BladeTable Insert a should Always be Level with the Table Miter Gauge Operation and AdjustmentAdjusting Table Insert Assembling Miter GaugeChanging the SAW Blade Aligning Miter Slots to BladeMachine USE Quick Operations ChecklistBack View KEY Parts and Safety Features on Your SAWCROSS-CUTTING Blade Guard and Splitter USECompound Mitering Never USE the Fence AS a CUT-OFF Gauge When CROSS-CUTTINGMitering Bevel CrosscuttingConstructing a Push Stick RippingBevel Ripping Using Moulding CutterheadFig. S15 Using Accessory Dado HeadFig. S18 Using Auxiliary Wood FacingPower Tool Institute TroubleshootingConstructing a Featherboard Constructing a Push Stick Push StickShelf Measurements MaintenanceAccessories ServiceWarranty Delta Machinery
Related manuals
Manual 100 pages 12.32 Kb