Campbell Hausfeld CHN10600 specifications Operating Instructions, Recommended Hookup

Page 4

Operating Instructions

Important Safety Instructions

 

 

 

 

 

 

 

 

 

 

1.

Disconnect the air

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Continued)

 

 

 

 

 

 

 

 

 

 

 

 

supply from the tool

 

 

 

 

 

Do not use any type of

 

 

 

 

 

 

 

 

 

 

 

Do not make any

 

 

 

 

 

 

 

to add lubricant.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

modifications to

reactive gases, including, but

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

not limited to, oxygen and

 

 

 

 

 

 

 

 

 

 

 

 

 

the tool without first obtaining written

 

 

 

 

 

2.

Turn the tool so the air

 

 

 

combustible gases, as a power source.

 

 

 

approval from Campbell Hausfeld. Do

 

 

 

Use filtered, lubricated, regulated

 

 

inlet is facing up. Place

 

 

 

not use the tool if any shields or guards

 

 

 

 

 

compressed air only. Use of a reactive

 

 

4-5 drops of 30 W non-

 

 

 

are removed or altered. Do not use the

 

 

 

 

 

tool as a hammer. Personal injury or

gas instead of compressed air may

 

 

detergent oil into air inlet.

 

 

 

cause the tool to explode which will

 

 

 

 

 

tool damage may occur.

 

 

Do not use detergent

 

 

cause death or serious personal injury.

 

 

 

 

 

 

Disconnect air

 

 

oils, oil additives, or air- tool oils.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

supply and release

 

 

 

 

 

 

 

 

 

 

 

 

Air tool oils contain solvents which

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tension from the pusher before

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

will damage the tool's internal

attempting to clear jams because

Use only a pressure-regulated

 

 

 

 

 

 

 

 

 

 

 

 

components.

 

 

fasteners can be ejected from the front

compressed air source to limit

 

 

100 psi

 

 

 

 

 

of the tool. Personal injury may occur.

the air pressure supplied to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

After adding oil, run

 

 

 

AIR SOURCE

the tool. The regulated pressure must

 

 

tool briefly. Wipe off

 

 

 

 

not exceed 100 psi. If the regulator

 

 

 

 

 

 

 

any excess oil from the

 

 

 

 

a. Never connect to an air source that

fails, the pressure delivered to the

 

 

 

 

 

 

 

cap exhaust.

 

 

 

 

is capable of exceeding 200 psi.

tool must not exceed 200 psi. The tool

 

 

 

 

 

 

 

 

 

 

could explode which will cause death or

 

RECOMMENDED HOOKUP

 

 

Over pressurizing the tool is able

 

 

 

serious personal injury.

 

 

 

 

 

 

 

 

to result in bursting, abnormal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAVE THESE INSTRUCTIONS

 

The illustration below shows the

 

 

operation, breakage of the tool or

 

 

recommended hookup for the tool.

 

 

DO NOT DISCARD

 

 

 

 

serious injury to persons. Use only

 

 

 

 

 

1.

The air compressor

 

 

 

 

 

clean, dry, regulated compressed air

 

 

 

 

 

 

 

 

 

 

 

 

 

60 psi

Operating Instructions

 

 

 

 

 

must be able to

 

 

 

Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

at the rated pressure or within the

 

 

 

 

 

 

 

 

 

psi

 

 

 

 

 

maintain a minimum

 

 

 

100

rated pressure range as marked on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Max.

 

LUBRICATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of 60 psi when the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the tool. Always verify prior to using

 

 

 

 

 

 

 

 

 

 

 

 

This tool requires lubrication before

 

 

tool is being used. An inadequate air

the tool that the air source has been

 

 

using the tool for the first time and

 

 

supply can cause a loss of power and

adjusted to the rated air pressure or

 

 

before each use. If an inline oiler is

 

 

inconsistent driving.

 

 

within the rated air-pressure range.

 

 

 

 

used, manual lubrication through the

2.

An oiler can be

 

 

 

 

 

b. Never use oxygen, carbon dioxide,

 

 

 

 

 

air inlet is not required on a daily basis.

 

 

used to provide oil

 

 

 

 

 

combustible gases or any bottled

 

 

 

 

 

 

 

 

 

 

The work surface

 

 

circulation through

 

 

 

 

 

gas as an air source for the tool.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

can become

 

 

 

 

 

the tool. A filter can

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Such gases are capable of explosion

 

 

 

 

 

 

 

 

 

 

 

 

 

damaged by excessive lubrication.

 

 

be used to remove liquid and solid

and serious injury to persons.

 

 

Proper lubrication is the owner’s

 

 

impurities which can rust or “gum

 

 

 

 

 

 

 

 

responsibility. Failure to lubricate the

 

 

 

 

 

 

 

 

 

 

 

 

up” internal parts of the tool.

 

 

 

 

 

 

 

 

 

 

tool properly will dramatically shorten

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the life of the tool and void your

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

warranty.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Recommended Hookup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Regulator

 

 

 

 

 

 

 

 

 

 

Quick

Quick Plug

Quick

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Coupler

 

 

 

 

 

 

 

 

 

 

 

 

Quick Plug

Coupler

(Optional)

(Optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Hose

Lubricator

Filter

www.chpower.com

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Table of Contents Safety GuidelinesImportant Safety Instructions DescriptionTool Components and Specifications Personal SafetyGeneral Work AreaService Tool USE and CareOperating Instructions Recommended HookupUser-Maintenance Instructions FastenersTroubleshooting Chart CHN10600 Limited Warranty What is not Covered Under this WarrantyTable des matières DéballageDirectives de Sécurité Importantes instructions de sécuritéDe sécurité Suite Importantes instructionsPièces détachées et fiche technique mécanisme de la loutil Utilisation ET Entretien DE L’OUTIL Importantes instructions de sécurité Suite11 Fr Mode d’emploi Branchement RecommandéBranchement Recommandé Source D’AIRMode d’emploi Suite AttachesNettoyer le chargeur Guide de Dépannage14 Fr 15 Fr Garantie Limitée 16 FrÍndice DescripciónDesempaque Medidas de SeguridadImportantes Continúa Instrucciones de SeguridadComponentes y Especificaciones de la Herramienta USO Y Cuidado DE LA Herramienta Instrucciones de Seguridad Importantes Continúa19 Sp Funcionamiento Instrucciones deConexión Recomendada Instrucciones de Funcionamiento Continúa Instrucciones de Uso y MantenimientoAlmacenaje SujetadoresNotas 22 SpGuía de Diagnóstico de Averías Hay una fuga de aire en elDebe reemplazar los anillos en O 23 SpGarantía Limitada 24 Sp

CHN10600 specifications

The Campbell Hausfeld CHN10600 is an innovative air compressor that combines efficiency and reliability for both home and professional use. Known for its versatility, this model stands out with a range of features that cater to various tasks, making it an essential tool for DIY enthusiasts and professionals alike.

One of the most notable features of the CHN10600 is its 3-gallon tank. This compact size strikes a perfect balance between portability and sufficient air storage, enabling users to operate tools for extended periods without frequent refilling. The 1.0 horsepower motor powers this compressor, delivering a maximum pressure of 100 PSI, which is ample for a variety of applications including inflating tires, powering pneumatic tools, and more.

The CHN10600 is equipped with an oil-free pump, which not only minimizes maintenance but also enhances usability. The oil-free design eliminates the need for regular oil changes, saving time and effort for users. This feature also contributes to the compressor's compact nature, making it lightweight and easy to transport, whether you are moving it from the garage to the workshop or taking it to a job site.

One of the standout technologies integrated into the CHN10600 is its low noise operation. This model is designed to operate quietly, making it ideal for residential areas or situations where noise reduction is a priority. The sound level is significantly lower than traditional compressors, allowing for a more comfortable working environment.

Furthermore, the Campbell Hausfeld CHN10600 boasts a user-friendly control panel that features easy-to-read gauges, making it simple for users to monitor pressure levels at a glance. The built-in regulator allows for precise adjustments, enabling users to tailor the output to the specific needs of their tools or projects.

Durability is a key characteristic of the CHN10600. It features a robust construction designed to withstand the rigors of frequent use, making it a reliable choice for both home and professional applications. With its combination of efficiency, low maintenance, and portability, the Campbell Hausfeld CHN10600 air compressor is a versatile and practical tool that meets the demands of various tasks while providing excellent performance. Whether you are inflating tires, brad nailing, or using airbrushes, this model delivers satisfying results with ease.
Top Page Image Contents