Grizzly G0609 owner manual Set Up Safety, Items Needed for Set Up, Unpacking, Description Qty

Page 13

SECTION 3: SET UP

Set Up Safety

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire set up pro- cess!

The Model G0609 is a heavy machine (1,036 lbs shipping weight). Use power lifting equipment to lift this jointer. Otherwise serious personal injury may occur

Items Needed for

Set Up

The following items are needed to complete the set up process, but are not included with your machine:

Description

 

Qty

• Safety Glasses (for each person)

1

Solvent

1

Shop Rags for Cleaning

As Needed

• Extra Person for Lifting Help

1

• Fork Lift, Engine Hoist, or Boom Crane

1

• Lifting Straps (900 lb. Capacity)

2

• Straightedge (see Page 18)

1

Phillips Screwdriver #2

1

Unpacking

The Model G0609 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the con- dition of your shipment, you should inventory the contents.

G0609 12" Parallelogram Jointer

-11-

Image 13
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer SafetyG0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingInventory Crate Contents QtyHardware and Tools Qty Hardware Recognition Chart Machine Placement Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerFence To install the fenceFence is Heavy To set up the pedestal switch Pedestal SwitchWinding Cutterhead Guard Components and Hardware Needed QtyChecking Outfeed Table Height Knife Setting JigTo check the outfeed table height Recommended CFM at Dust Port ... CFM Dust Port Test RunTo test run the machine Operations Operation Safety Basic ControlsCorrect and incorrect grain alignment Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH9291-12 Shellix Spiral Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesCleaning MaintenanceSchedule Unpainted Cast IronDate Approximate Hours Of Use Maintenance Performed Maintenance LogTroubleshooting ServiceMotor & Electrical Cutting Inspecting Knives Adjusting/Replacing KnivesTools Needed Qty To inspect the knivesTo adjust/replace the knives Cutterhead profile diagramPage Checking Outfeed Table Checking/Adjusting Table ParallelismTo check the outfeed table parallelism To adjust the table parallelism Adjusting Table ParallelismChecking Infeed Table To check the infeed table parallelismTo set the outfeed table height Setting Outfeed Table HeightSetting Infeed Table Calibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopTo replace the V-belts Belts Pulley AlignmentTo align the pulleys Page Motor junction box G0609 Electrical ComponentsG0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts ListTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page