Grizzly G0609 Knife Setting Jig, Checking Outfeed Table Height, To check the outfeed table height

Page 20

Knife Setting Jig

Assemble the jig as shown in Figure 13.

Figure 13. Knife setting jig assembly.

Checking Outfeed

Table Height

The outfeed table MUST be level with the knives when they are at top-dead-center or the workpiece cannot be feed across the jointer safely. The outfeed table height is factory set, but we recom- mend that you check it to make sure that it didn’t change during shipping.

To check the outfeed table height:

1.Place a straightedge on the outfeed table so it extends over the cutterhead.

2.Rotate the cutterhead pulley until one of the knives is at top-dead-center (TDC), as illus- trated in Figure 14.

-18-

��������

������

Figure 14. Cutterhead knife at top-dead center.

When correctly set, the knife will barely touch the straightedge, as shown in Figure 15.

—If your outfeed table is correctly set, no adjustments are necessary.

—If the knife lifts the straightedge off the table or it is below the straightedge, then the outfeed table must be re-set. Refer to Setting Outfeed Table Height on Page 39.

������������

������� ������

Figure 15. Using a straightedge to align outfeed

table height with knife at TDC.

G0609 12" Parallelogram Jointer

Image 20
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram JointerG0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit RequirementsSET UP Set Up SafetyItems Needed for Set Up UnpackingHardware and Tools Qty Crate Contents QtyInventory Hardware Recognition Chart Clean Up Machine PlacementSite Considerations Floor LoadMoving & Placing Jointer Mounting to Shop FloorBolting to Concrete Floors To lift the jointerFence is Heavy To install the fenceFence Pedestal Switch To set up the pedestal switchWinding Cutterhead Guard Components and Hardware Needed QtyTo check the outfeed table height Knife Setting JigChecking Outfeed Table Height To test run the machine Dust Port Test RunRecommended CFM at Dust Port ... CFM Operation Safety Basic Controls OperationsStock Inspection and Requirements Correct and incorrect grain alignmentMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerAccessories H9291-12 Shellix Spiral CutterheadG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Maintenance CleaningSchedule Unpainted Cast IronMaintenance Log Date Approximate Hours Of Use Maintenance PerformedMotor & Electrical ServiceTroubleshooting Cutting Adjusting/Replacing Knives Inspecting KnivesTools Needed Qty To inspect the knivesCutterhead profile diagram To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismChecking Outfeed Table Adjusting Table Parallelism To adjust the table parallelismChecking Infeed Table To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Setting Fence Stops Calibrating DepthScale To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopTo align the pulleys Belts Pulley AlignmentTo replace the V-belts Page G0609 Electrical Components Motor junction boxG0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List DescriptionTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page