Grizzly G0609 owner manual Cutterhead profile diagram, To adjust/replace the knives

Page 37

Knife Setting Jig Method: Both tables are low- ered to fit the jig on the cutterhead, as shown in Figure 43, and the knife heights are set to just touch the middle pad of the jig.

The knife setting jig makes it easy to ensure that the knives project out of the cutterhead evenly. After using the knife setting jig to set the knives, you have to re-adjust the outfeed table height to ensure that it is even with the knives at their high- est point of rotation. If you are using the positive stops on the tables, they will need to also be reset before operation.

Figure 43. Using knife setting jig to set knife

height.

The Model G0609 comes with jack screws inside the cutterhead to adjust the knives (see Figure 44).

Figure 44. Cutterhead profile diagram.

Tools Needed

Qty

Straightedge

1

Knife Setting Jig (Optional)

1

Hex Wrench 3mm

1

Wrench 10mm

1

To adjust/replace the knives:

 

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Loosen the set screws shown in Figure 10, Page 17, remove the cutterhead guard, and move the fence back as far as it will go.

3.Open the pulley cover to expose the cutterhead pulley.

4.Rotate the cutterhead pulley to get access to one of the cutterhead knives.

5.Loosen the cutterhead gib bolts, starting in the middle, and alternating back and forth until all of the gib bolts are loose, but not fall- ing out.

—If this is the first time you are setting the knives, remove the gib and knife from the cutterhead.

6.Remove and clean the gibs and clean inside the cutterhead slot to remove all pitch or saw- dust. Coat the knives and gibs with a metal protectant (Page 27), then fit the gibs back in the cutterhead with the new knives.

G0609 12" Parallelogram Jointer

-35-

Image 37
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer SafetyG0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingInventory Crate Contents QtyHardware and Tools Qty Hardware Recognition Chart Machine Placement Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerFence To install the fenceFence is Heavy To set up the pedestal switch Pedestal SwitchWinding Cutterhead Guard Components and Hardware Needed QtyChecking Outfeed Table Height Knife Setting JigTo check the outfeed table height Recommended CFM at Dust Port ... CFM Dust Port Test RunTo test run the machine Operations Operation Safety Basic ControlsCorrect and incorrect grain alignment Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH9291-12 Shellix Spiral Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesCleaning MaintenanceSchedule Unpainted Cast IronDate Approximate Hours Of Use Maintenance Performed Maintenance LogTroubleshooting ServiceMotor & Electrical Cutting Inspecting Knives Adjusting/Replacing KnivesTools Needed Qty To inspect the knivesTo adjust/replace the knives Cutterhead profile diagramPage Checking Outfeed Table Checking/Adjusting Table ParallelismTo check the outfeed table parallelism To adjust the table parallelism Adjusting Table ParallelismChecking Infeed Table To check the infeed table parallelismTo set the outfeed table height Setting Outfeed Table HeightSetting Infeed Table Calibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopTo replace the V-belts Belts Pulley AlignmentTo align the pulleys Page Motor junction box G0609 Electrical ComponentsG0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts ListTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page