Grizzly G0609 Winding Cutterhead Guard, Pedestal Switch, Components and Hardware Needed Qty

Page 19

Winding Cutterhead

Guard

Though the cutterhead guard is pre-installed, you should check to make sure it works.

1.Pull the guard back and let it go. The guard should spring back over the cutterhead.

—If the guard drags across the table, loosen the set screws on the guard, raise it slight- ly, then tighten the set screws.

—If the guard does not spring back over the cutterhead, loosen the set screws on the jointer shown in Figure 10, hold the guard over the cutterhead, and wind the shaft collar clockwise. Tighten the set screws. Check to see if the guard works and adjust the collar as needed.

Shaft

Collar

Set

Screws

Figure 10. Loosening set screws.

G0609 12" Parallelogram Jointer

Pedestal Switch

The pedestal switch is upside down for shipping purposes.

Components and Hardware Needed:		Qty
• Flat Washers 10mm (Pedestal)		2
• Lock Washers 10mm (Pedestal)		2
•	Cap Screws M10-1.5 x 25 (Pedestal)	2
•	Pedestal Switch	1

To set up the pedestal switch:

1.Remove the M10-1.5 x 25 cap screws and flat washers shown in Figure 11.

2.Turn the pedestal upright and fasten it to the jointer with the cap screws and washers removed in Step 1, as shown in Figure 12.

Figure 11. Location of pedestal mounting

hardware (one side shown).

Figure 12. Mounting pedestal in upright position. -17-

Image 19

Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer SafetyG0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-PhaseUnpacking SET UPSet Up Safety Items Needed for Set UpInventory Crate Contents QtyHardware and Tools Qty Hardware Recognition Chart Floor Load Clean UpMachine Placement Site ConsiderationsTo lift the jointer Moving & Placing JointerMounting to Shop Floor Bolting to Concrete FloorsFence To install the fenceFence is Heavy Components and Hardware Needed Qty Pedestal SwitchTo set up the pedestal switch Winding Cutterhead GuardChecking Outfeed Table Height Knife Setting JigTo check the outfeed table height Recommended CFM at Dust Port ... CFM Dust Port Test RunTo test run the machine Operations Operation Safety Basic ControlsCorrect and incorrect grain alignment Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSS AccessoriesH9291-12 Shellix Spiral Cutterhead G3631-Jointer/Planer Knife HoneGrizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesUnpainted Cast Iron MaintenanceCleaning ScheduleDate Approximate Hours Of Use Maintenance Performed Maintenance LogTroubleshooting ServiceMotor & Electrical Cutting To inspect the knives Adjusting/Replacing KnivesInspecting Knives Tools Needed QtyTo adjust/replace the knives Cutterhead profile diagramPage Checking Outfeed Table Checking/Adjusting Table ParallelismTo check the outfeed table parallelism To check the infeed table parallelism Adjusting Table ParallelismTo adjust the table parallelism Checking Infeed TableTo set the outfeed table height Setting Outfeed Table HeightSetting Infeed Table To calibrate the depth scale Setting Fence StopsCalibrating Depth ScaleTo set the 45 outward fence stop To set the 90˚ fence stopTo replace the V-belts Belts Pulley AlignmentTo align the pulleys Page Motor junction box G0609 Electrical ComponentsG0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts ListTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page