Grizzly Essential Guide to Operating the G0609 Biscuit Joiner

Page 21

Dust Port

 

Test Run

 

 

 

 

 

 

DO NOT operate the Model G0609 with- out an adequate dust collection system. This machine creates substantial amounts of wood dust while operating. Failure to use a dust collection system can result in short and long-term respiratory illness.

The dust port is installed at the factory, so just attach it to an adequate dust collection system.

Recommended CFM at Dust Port: .... 615 CFM

Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must take into account many variables, including the CFM rating of the dust collector, the length of hose between the dust collector and the machine, the amount of branches or wyes, and the amount of other open lines throughout the system. Explaining this cal- culation is beyond the scope of this manual. If you are unsure of your system, consult an expert or purchase a good dust collection "how-to" book.

G0609 12" Parallelogram Jointer

Once the assembly is complete, test run your machine to make sure it runs properly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 32.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Connect the machine to the power source.

2.Twist the STOP button so it pops out.

3.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

4.Make sure all tools and objects used during set up are cleared away from the machine.

5.Turn the machine ON.

6.Press the STOP button, then restart the jointer.

7.Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises.

—Immediately turn the jointer OFF if you suspect any problems, and refer to Page 32 to troubleshoot/fix any problems before starting the jointer again.

If the source of an unusual noise or vibra- tion is not readily apparent, contact our Technical Support at (360) 546-9663.

-19-

Image 21
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer SafetyG0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingCrate Contents Qty InventoryHardware and Tools Qty Hardware Recognition Chart Machine Placement Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerTo install the fence FenceFence is Heavy To set up the pedestal switch Pedestal SwitchWinding Cutterhead Guard Components and Hardware Needed QtyKnife Setting Jig Checking Outfeed Table HeightTo check the outfeed table height Dust Port Test Run Recommended CFM at Dust Port ... CFMTo test run the machine Operations Operation Safety Basic ControlsCorrect and incorrect grain alignment Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH9291-12 Shellix Spiral Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesCleaning MaintenanceSchedule Unpainted Cast IronDate Approximate Hours Of Use Maintenance Performed Maintenance LogService TroubleshootingMotor & Electrical Cutting Inspecting Knives Adjusting/Replacing KnivesTools Needed Qty To inspect the knivesTo adjust/replace the knives Cutterhead profile diagramPage Checking/Adjusting Table Parallelism Checking Outfeed TableTo check the outfeed table parallelism To adjust the table parallelism Adjusting Table ParallelismChecking Infeed Table To check the infeed table parallelismTo set the outfeed table height Setting Outfeed Table HeightSetting Infeed Table Calibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopBelts Pulley Alignment To replace the V-beltsTo align the pulleys Page Motor junction box G0609 Electrical ComponentsG0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts ListTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page