Grizzly G0609 owner manual Setting Outfeed Table Height, To set the outfeed table height

Page 41

 

 

Set Screw

Eccentric

 

Location

Bushing

 

 

 

 

 

 

 

 

Figure 52. Eccentric bushing and set screw

location.

3.Place the straightedge in one of the positions shown in Figure 49, and adjust the table (a small hammer and punch or pin-type span- ner wrench may be necessary to turn the eccentric bushings) so that the straightedge touches the cutterhead while lying flat across the outfeed table. Repeat this step with each of the remaining straightedge positions as many times as necessary until the outfeed table is parallel with the cutterhead to within 0.010"-0.012".

Note: Setting the outfeed table parallel to the cutterhead within 0.010"-0.012" will produce high quality results. Exceeding this number will produce minimal gain.

4.Tighten/replace the set screws in the eccen- tric bushings on the outfeed table.

5.Remove the set screw from each of the four eccentric bushings under the infeed table, and loosen the set screws underneath those removed set screws.

6.Place the straightedge halfway across the infeed table and halfway over the outfeed table, and adjust the infeed table even with the outfeed table, as shown in Figure 50.

7.Place the straightedge in one of the posi- tions shown in Figure 51, and adjust the eccentric bushings under the infeed table so the straightedge lies flat against both tables. Repeat this step with each of the remaining straightedge positions as many times as nec- essary until the infeed table is parallel with the outfeed table.

8.Tighten/replace the set screws in the eccen- tric bushings on the infeed table.

G0609 12" Parallelogram Jointer

9.Set the outfeed table height (refer to the next sub-section).

10.Set the knives (refer to Page 35).

11.Reinstall the cutterhead guard and fence.

Setting Outfeed

Table Height

The outfeed table height must be even with the top of the cutterhead knives. If the outfeed table is set too low, there will be snipe. If the outfeed table is set too high, the workpiece will hit the edge of the outfeed table during operation, increasing the chance of kickback.

Tools Needed

Qty

Straightedge

1

Wrench 17mm

1

Wrench 19mm

1

Hex Wrench 5mm

1

Hex Wrench 3mm

1

Feeler Gauge(s) 0.062"

1

To set the outfeed table height:

 

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Check/adjust the table parallelism.

3.Loosen the set screws shown in Figure 10, Page 17, remove the guard, and remove the fence.

4.Loosen the outfeed table lock located at the front of the machine, and loosen the jam nuts and positive stop bolts located at the back of the machine (see Figure 47).

-39-

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer SafetyG0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingHardware and Tools Qty Crate Contents QtyInventory Hardware Recognition Chart Machine Placement Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerFence is Heavy To install the fenceFence To set up the pedestal switch Pedestal SwitchWinding Cutterhead Guard Components and Hardware Needed QtyTo check the outfeed table height Knife Setting JigChecking Outfeed Table Height To test run the machine Dust Port Test RunRecommended CFM at Dust Port ... CFM Operations Operation Safety Basic ControlsCorrect and incorrect grain alignment Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH9291-12 Shellix Spiral Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesCleaning MaintenanceSchedule Unpainted Cast IronDate Approximate Hours Of Use Maintenance Performed Maintenance LogMotor & Electrical ServiceTroubleshooting Cutting Inspecting Knives Adjusting/Replacing KnivesTools Needed Qty To inspect the knivesTo adjust/replace the knives Cutterhead profile diagramPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismChecking Outfeed Table To adjust the table parallelism Adjusting Table ParallelismChecking Infeed Table To check the infeed table parallelismTo set the outfeed table height Setting Outfeed Table HeightSetting Infeed Table Calibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopTo align the pulleys Belts Pulley AlignmentTo replace the V-belts Page Motor junction box G0609 Electrical ComponentsG0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts ListTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page
Top Page Image Contents