Grizzly G0609 owner manual Setting Infeed Table

Page 42

5.Place the straightedge on the outfeed table so it hangs over the cutterhead, and lower the outfeed table until the straightedge is 0.062" (1⁄16") above the cutterhead body, as determined by using the feeler gauges (see Figure 53).

��

��

��

��

Figure 53. Using feeler gauges to set outfeed

table height.

6.Tighten the outfeed table lock located at the front of the machine, and tighten the positive stop bolts and jam nuts located at the back of the machine (see Figure 47).

7.Set the knife heights (Page 34) to the new outfeed table height.

-40-

Setting Infeed Table

The infeed table on the Model G0609 has positive stop bolts that, when properly set up, allow the operator to quickly adjust the infeed table between finish/final cuts and shaping/heavy cuts.

We recommend setting the minimum depth of cut to 1⁄32" and the maximum depth of cut to 1⁄8" for most operations. DO NOT exceed 1⁄8" cut per pass on this machine or kickback and serious injury may occur!

Each positive stop bolt (Figure 54) controls the top or bottom range of the table movement. The jam nuts lock the positive stop bolts in position so they won't move during operation.

Jam Nut

Jam Nut

Bottom		Top Height
Height

Figure 54. Positive stop bolts for infeed table.

G0609 12" Parallelogram Jointer

Image 42

Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram JointerG0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit RequirementsItems Needed for Set Up SET UPSet Up Safety UnpackingCrate Contents Qty InventoryHardware and Tools Qty Hardware Recognition Chart Site Considerations Clean UpMachine Placement Floor LoadBolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointerTo install the fence FenceFence is Heavy Winding Cutterhead Guard Pedestal SwitchTo set up the pedestal switch Components and Hardware Needed QtyKnife Setting Jig Checking Outfeed Table HeightTo check the outfeed table height Dust Port Test Run Recommended CFM at Dust Port ... CFMTo test run the machine Operation Safety Basic Controls OperationsStock Inspection and Requirements Correct and incorrect grain alignmentMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerG3631-Jointer/Planer Knife Hone AccessoriesH9291-12 Shellix Spiral Cutterhead H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Schedule MaintenanceCleaning Unpainted Cast IronMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService TroubleshootingMotor & Electrical Cutting Tools Needed Qty Adjusting/Replacing KnivesInspecting Knives To inspect the knivesCutterhead profile diagram To adjust/replace the knivesPage Checking/Adjusting Table Parallelism Checking Outfeed TableTo check the outfeed table parallelism Checking Infeed Table Adjusting Table ParallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Scale Setting Fence StopsCalibrating Depth To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopBelts Pulley Alignment To replace the V-beltsTo align the pulleys Page G0609 Electrical Components Motor junction boxG0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List DescriptionTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page