Grizzly G0609 owner manual Belts Pulley Alignment, To replace the V-belts, To align the pulleys

Page 45

V-Belts

 

Pulley Alignment

 

 

 

 

 

 

Inspect the V-belts closely; if you notice fraying, cracking, glazing, or any other damage, replace the belts. A worn or damaged V-belt will not pro- vide optimum power transmission from the motor to the drum and feed belt.

V-belt removal and replacement is simply a mat- ter of loosening the V-belts, rolling them off of the pulleys, replacing them with new belts, then retensioning them.

Tools Needed:

Qty

Wrench or Socket 19mm

................................... 1

To replace the V-belts:

 

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Open the pulley cover.

3.Loosen the fasteners on the tension rod that hold the motor to the bracket (Figure 61).

Tension

Rod

Fasteners

Figure 61. Fasteners needed to be loosened for

V-belt replacement.

4.Lift the motor up and slide the V-belts off of the motor pulley and cutterhead pulley.

5.Slide the new belts onto the pulleys, tighten the motor bracket fasteners, and close the pulley cover.

G0609 12" Parallelogram Jointer

Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplaner) for optimum performance.

Each pulley can be adjusted by loosening the motor mount fasteners, sliding the motor in or out, and retightening the fasteners to lock the motor pulley in place.

Tools Needed:

Qty

Wrench or Socket 17mm

................................... 1

To align the pulleys:

 

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Open the pulley cover.

3.Visually check the alignment of the two pul- leys to make sure that they are aligned and that the V-belts are straight up and down (see Figure 62).

Cutterhead

Pulley

���������

Motor

Pulley

Figure 62. Pulleys aligned.

—If the pulleys are aligned, tighten the motor mounts and go to Step 8.

—If the pulleys are NOT aligned, do Steps 4 & 5.

-43-

Image 45
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer SafetyG0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingCrate Contents Qty InventoryHardware and Tools Qty Hardware Recognition Chart Machine Placement Clean UpSite Considerations Floor LoadMounting to Shop Floor Moving & Placing JointerBolting to Concrete Floors To lift the jointerTo install the fence FenceFence is Heavy To set up the pedestal switch Pedestal SwitchWinding Cutterhead Guard Components and Hardware Needed QtyKnife Setting Jig Checking Outfeed Table HeightTo check the outfeed table height Dust Port Test Run Recommended CFM at Dust Port ... CFMTo test run the machine Operations Operation Safety Basic ControlsCorrect and incorrect grain alignment Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingTo rabbet cut on the jointer Rabbet CuttingH9291-12 Shellix Spiral Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesCleaning MaintenanceSchedule Unpainted Cast IronDate Approximate Hours Of Use Maintenance Performed Maintenance LogService TroubleshootingMotor & Electrical Cutting Inspecting Knives Adjusting/Replacing KnivesTools Needed Qty To inspect the knivesTo adjust/replace the knives Cutterhead profile diagramPage Checking/Adjusting Table Parallelism Checking Outfeed TableTo check the outfeed table parallelism To adjust the table parallelism Adjusting Table ParallelismChecking Infeed Table To check the infeed table parallelismTo set the outfeed table height Setting Outfeed Table HeightSetting Infeed Table Calibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopBelts Pulley Alignment To replace the V-beltsTo align the pulleys Page Motor junction box G0609 Electrical ComponentsG0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts ListTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page