Grizzly G0609 owner manual

Page 38

7.Adjusting the knife heights:

a.Using a 3mm hex wrench, find the jack screws through the access holes in the cutterhead (Figure 45) and rotate the jack screws to raise or lower the knife. When the knife is set correctly, it will barely touch the bottom of the straight- edge or the knife setting jig middle pad.

b.Snug the gib bolts tight enough to just hold the knife in place.

c.Repeat on the other side of the cutterhead.

d.Repeat Steps 5–7with the rest of the knives.

Jack Screw

Access Hole

Figure 45. Jack screw access hole.

-36-

8.Rotate the cutterhead to the first knife you started with. Slightly tighten all the gib bolts, starting at the ends and working your way to the middle by alternating left and right (Figure 46). Repeat this step on the rest of the knives.

5

3

1

2

4

6

Figure 46. Gib bolt tightening sequence.

9.Repeat Step 8.

10.Repeat Step 8, but final tighten each gib bolt.

11.If you used the knife setting jig to set the knife heights, use the straightedge to adjust the outfeed table height evenly with the knives at top dead center (the highest point in their rotation). If you used the straightedge to set the knife heights, skip to the next step.

12.Replace the cutterhead guard, wind the shaft collar, and tighten the set screws.

13.Close the pulley cover.

G0609 12" Parallelogram Jointer

Image 38
Contents Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram JointerG0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit RequirementsItems Needed for Set Up SET UPSet Up Safety UnpackingHardware and Tools Qty Crate Contents QtyInventory Hardware Recognition Chart Site Considerations Clean UpMachine Placement Floor LoadBolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointerFence is Heavy To install the fenceFence Winding Cutterhead Guard Pedestal SwitchTo set up the pedestal switch Components and Hardware Needed QtyTo check the outfeed table height Knife Setting JigChecking Outfeed Table Height To test run the machine Dust Port Test RunRecommended CFM at Dust Port ... CFM Operation Safety Basic Controls OperationsStock Inspection and Requirements Correct and incorrect grain alignmentMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerG3631-Jointer/Planer Knife Hone AccessoriesH9291-12 Shellix Spiral Cutterhead H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Schedule MaintenanceCleaning Unpainted Cast IronMaintenance Log Date Approximate Hours Of Use Maintenance PerformedMotor & Electrical ServiceTroubleshooting Cutting Tools Needed Qty Adjusting/Replacing KnivesInspecting Knives To inspect the knivesCutterhead profile diagram To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismChecking Outfeed Table Checking Infeed Table Adjusting Table ParallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Scale Setting Fence StopsCalibrating Depth To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopTo align the pulleys Belts Pulley AlignmentTo replace the V-belts Page G0609 Electrical Components Motor junction boxG0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List DescriptionTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page