Grizzly G0763 owner manual Site Considerations

Page 18

Site Considerations

Weight Load

Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest work- piece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the main- tenance and service described in this manual.

See below for required space allocation.

Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.

Physical Environment

The physical environment where the machine is operated is important for safe operation and lon- gevity of machine components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemi- cals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41°–104°F; the relative humidity range exceeds 20–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave access to a means of disconnecting the power source or engaging a lockout/tagout device, if required.

Lighting

Lighting around the machine must be adequate enough that operations can be performed safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.

Wall

30" Minimum

Clearance

46"

79"

Figure 10. Minimum working clearances.

-16-	Model G0763 (Mfg. Since 8/13)

Image 18

Contents Model G0763 18 Surface Grinder Page Table of Contents Introduction Machine Description Manual AccuracyContact Info Identification Master Power Switch Basic ControlsGrinding Wheel & Coolant Controls Power Feed Controls HandwheelsMachine Data Sheet Magnetic Chuck Info Safety Safety Instructions for MachineryPage Additional Safety for Surface Grinders Full-Load Current Rating Power SupplyAvailability Circuit Requirements forMinimum Gauge Size 14 AWG Grounding InstructionsExtension Cords 50 ftUnpacking SetupNeeded for Setup Description QtyInventory Small parts inventoryCleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Lifting & Placing To lift and place the machineAssembly To assemble the surface grinderCable orientation on pulley Open End Pulley Page Power Connection To connect the power supply to the machineTest Run To test run the machinePage Operations Operation OverviewGrit Size Wheel SelectionAbrasive Type GradeWheel Inspection Ring Test To inspect a wheel for damageTo perform a ring test To balance the grinding wheel assembly Wheel BalancingTools Needed Qty Mounting Wheel To mount wheel assemblyMounting/Removing Wheel Items Needed QtyPage To remove wheel assembly Wheel DressingRemoving Wheel Power Feeds To set up the power feeds to work togetherTool Needed Qty Model G0763 Mfg. Since 8/13 Accessories Friable Surface Grinding Wheels, Aluminum OxideH5618-Parallels for Magnetic Chuck Schedule MaintenanceCleaning Protecting DailyLubrication One-Shot OilerOil Sump Hazards Coolant SystemTable Ball Bearing Strips To lubricate table ball bearing stripsChanging Coolant Wheel StorageCheck/Adding Coolant To change coolantService TroubleshootingSymptom Possible Cause Possible Solution Wiring Wiring Safety InstructionsWiring Overview Control Panel Electrical Cabinet WiringPower Feed Control Panel 220 VAC PumpElectrical panel and control panel wiring Electrical Panel & Control PanelControl Panel Wiring Control Panel Viewed from behindElectrical Cabinet Wiring Power Feed Control Panel Power feed controls wiring Model G0763 Mfg. Since 8/13Coolant Pump Motor 220V Prewired Motor Wiring DiagramsSpindle Motor Wiring clockwise Coolant Pump Motor Rewired toParts BaseColumn 134Description Motor & Downfeed System DescriptionSaddle 405 406 402 407 404 419 403 417 409 410 412 416 418 503 505 511 507 508510 502 509 501 Accessories Electrical Cabinet Main Control Panel 715Power Feed Control Box 722 723 733 721 724Labels & Cosmetics Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns