ARC Rays can burn eyes and skin | Miller Electric S-75D, S-75S

ARC RAYS can burn eyes and skin.

Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.

DWear an approved welding helmet fitted with a proper shade of fil- ter lenses to protect your face and eyes when welding or watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).

DWear approved safety glasses with side shields under your helmet.

DUse protective screens or barriers to protect others from flash, glare and sparks; warn others not to watch the arc.

DWear protective clothing made from durable, flame-resistant mate- rial (leather, heavy cotton, or wool) and foot protection.

WELDING can cause fire or explosion.

Welding on closed containers, such as tanks, drums, or pipes, can cause them to blow up. Sparks can fly off from the welding arc. The flying sparks, hot workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause sparks, explosion, overheating, or fire. Check and be sure the area is safe before doing any welding.

DRemove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers.

DDo not weld where flying sparks can strike flammable material.

DProtect yourself and others from flying sparks and hot metal.

DBe alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas.

DWatch for fire, and keep a fire extinguisher nearby.

DBe aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.

DDo not weld on closed containers such as tanks, drums, or pipes, unless they are properly prepared according to AWS F4.1 (see Safety Standards).

DConnect work cable to the work as close to the welding area as practical to prevent welding current from traveling long, possibly unknown paths and causing electric shock, sparks, and fire hazards.

DDo not use welder to thaw frozen pipes.

DRemove stick electrode from holder or cut off welding wire at contact tip when not in use.

DWear oil-free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes, and a cap.

DRemove any combustibles, such as a butane lighter or matches, from your person before doing any welding.

DFollow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL can injure eyes.

DWelding, chipping, wire brushing, and grinding cause sparks and flying metal. As welds cool, they can throw off slag.

DWear approved safety glasses with side shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

DShut off shielding gas supply when not in use.

D Always ventilate confined spaces or use approved air-supplied respirator.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

DAllow cooling period before working on gun or

torch.

DTo handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

MAGNETIC FIELDS can affect pacemakers.

D Pacemaker wearers keep away.

D Wearers should consult their doctor before going near arc welding, gouging, or spot welding operations.

NOISE can damage hearing.

Noise from some processes or equipment can damage hearing.

DWear approved ear protection if noise level is high.

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas cylinders are normally part of the welding process, be sure to treat them carefully.

DProtect compressed gas cylinders from excessive heat, mechani- cal shocks, physical damage, slag, open flames, sparks, and arcs.

DInstall cylinders in an upright position by securing to a stationary support or cylinder rack to prevent falling or tipping.

DKeep cylinders away from any welding or other electrical circuits.

DNever drape a welding torch over a gas cylinder.

DNever allow a welding electrode to touch any cylinder.

DNever weld on a pressurized cylinder − explosion will result.

DUse only correct shielding gas cylinders, regulators, hoses, and fit- tings designed for the specific application; maintain them and associated parts in good condition.

DTurn face away from valve outlet when opening cylinder valve.

DKeep protective cap in place over valve except when cylinder is in use or connected for use.

DUse the right equipment, correct procedures, and sufficient num- ber of persons to lift and move cylinders.

DRead and follow instructions on compressed gas cylinders, associated equipment, and Compressed Gas Association (CGA) publication P-1 listed in Safety Standards.

OM-223 605 Page 2

S-75S, S-75D specifications

Miller Electric is renowned for its cutting-edge welding and fabrication technology, and the S-75D and S-75S models stand out in their lineup, highlighting excellence in performance and versatility. Designed for both professional welders and industrial applications, these power sources are equipped to handle a variety of welding processes, from MIG to Flux-Core welding.

The Miller Electric S-75D is characterized by its robust construction and advanced technologies. One of its main features is the Auto-Set function, which simplifies the setup process by automatically adjusting the parameters based on the material thickness and wire size. This ensures optimal welding performance, providing welders with confidence in their work. Additionally, the S-75D is equipped with a powerful inverter design, offering increased efficiency and portability. Weighing significantly less than traditional transformer-based units, the S-75D allows for easier transportation to job sites without compromising on power.

On the other hand, the S-75S model incorporates several user-centric enhancements. With a focus on operational ease, it includes a large, intuitive digital display that provides real-time feedback on welding parameters. This feature allows for quick adjustments, ensuring that welders can maintain control over their projects. Furthermore, the S-75S boasts a duty cycle of up to 60%, making it ideal for heavy industrial applications where continuous operation is critical.

Both models share several key technologies that enhance their performance. The Wind Tunnel Technology, for instance, provides superior cooling capabilities, protecting internal components from dust and debris, which prolongs the life of the machine. Additionally, the Power Feed system supports large spools of wire, reducing the frequency of spool changes during long projects.

In terms of characteristics, the S-75D and S-75S are designed with durability in mind. They feature rugged chassis construction and high-quality components that withstand harsh working environments. Furthermore, both machines are equipped to operate in various settings, including fabrication shops, construction sites, and maintenance applications.

In summary, the Miller Electric S-75D and S-75S models represent the pinnacle of welding equipment innovation. With features like Auto-Set, robust duty cycles, intuitive displays, and advanced cooling technologies, they are engineered to meet the demands of skilled welders who seek efficiency, reliability, and high-quality performance in their work. These power sources are ideal for tackling complex welding tasks while ensuring user-friendly operation and durability in any environment.