Miller Electric S-75D, S-75S manual Diagnostics, Indicated Error, Error Indications

Page 26

7-2. Diagnostics

1 Wrapper

2 Motor Control Board PC1

3 LED3

4 P2

3

2

 

1

4

Front panel is shown removed for purpose of illustration only. In actual use, front panel would be in place.

Display On

LED3 Sequence On

 

Meter

 

Motor Control Board PC1

Indicated Error

(If Equipped)

 

 

 

 

 

 

 

HELP 11

1

Blink

Communication Error

HELP 12

2

Blinks

Trigger Error

HELP 13

3

Blinks

Tach Error

HELP 14

*4 Blinks

Motor Error

*Since blink On time and blink Off time are equal in a four-blink cycle, the four−blink sequence appears as constant blinking.

Ref. 802 687

Error Indications

Error conditions are indicated by LED3 on PC1 or on display (on models with meters). To view LED3, turn Off unit, remove wrapper, and turn unit On. LED3 is most easily observed from the left side of the unit.

The LED blinks in a 2.5 second cycle. The number of blinks in this period indicates the type of error.

The priority of the errors is related to the num- ber of blinks indicating the error. The more blinks, the more severe the error (motor error is top priority). A higher priority error overrides

a lower one (if a motor error and a communica- tion error existed, the light would blink four times for the motor error).

The communication error occurs 2.5 sec- onds after a loss of communication between the motor and the meter board (if equipped). The user may continue to weld with this er- ror. The error may be cleared by turning power Off, waiting a minimum of two sec- onds, and turning power On.

The trigger error occurs if the user has the trigger held for more than two minutes with- out striking an arc (providing current over- ride is not enabled), or if the user holds the

trigger past the postflow phase in a timed weld. This error also occurs if the trigger is held when the feeder is powered up. The er- ror may be cleared by releasing the trigger.

The tach error occurs 2 seconds after the loss of tachometer feedback. The user may continue to weld with this error. The motor speed is regulated through the monitoring of voltage and current.

The motor error indicates that the motor has been drawing too much current for too long. To remedy this, reduce the wire feed speed or the wire feeder torque load/duty cycle.

OM-223 605 Page 22

Image 26
Contents Description OM-223 605AProcesses From Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux Signifie Note n’est pas relatif à la sécuritéDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaquesKeep your head out of the fumes Disconnect input plug or power before working on machineDrive rolls can injure fingers Symbols And Definitions Site Selection SpecificationsWelding Overall Maximum Wire Feed RatingTions 0 to 350 Amps, and 350 Amps and above Rear Panel Connections And Rotating Drive AssemblyWeld Cable Weld Cable Screw Screw Size .375 − 16 X Amps and above Weld connection To 350 AmpsPin Plug PLG12 Information Wire Type, Size, And Feed Speed Capability TableInstalling Drive Rolls Gun Recommendation TableInstall PD inlet guide Installing PD Continuous Wire GuidesInstalling PD continuous wire guides with PD drive rolls Identified by initials PD and a part number on drive rollTools Needed 16, 3/32 Installing Non-PD Old Style Wire GuidesInstalling wire guides with non- PD old-style drive rolls Installing Welding Gun Wire Slips Pressure assembly Drive RollsNo Wire Slip End Of LinerManually Adjusted Run-In S1-1 And S1-2 Setting Internal DIP SwitchesRun-In Disabled S1-1 S1-1 And S1-2Digital Meter DIP Switch Setting Equipment DIP Switch Settings For Models With Meters OnlyRemove wrapper Install wrapper when finished Inches/Minute Meters/Minute Tools Needed OM-223 605Jog/Purge And Trigger Hold Power SwitchPower Switch Disconnect power before maintaining Routine MaintenanceYou can adjust the preset volt Clean Repair Replace Tighten Unreadable WeldError Indications DiagnosticsIndicated Error Trouble Remedy TroubleshootingDisconnect power before troubleshooting − Electrical Diagram OM-223 605 Main Assembly 21 FigPart Description Quantity Figures 9-3Control Box Diagram Part Quantity Model Marking Description 75S 75D Drive Assembly, Wire Drive Assembly With Motor Drive Assembly, Wire -1ItemPD Precision Drive and Old-Style Drive Rolls and Guides GuideStart Your Professional Welding Career Now Material Thickness Reference Chart Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s

S-75S, S-75D specifications

Miller Electric is renowned for its cutting-edge welding and fabrication technology, and the S-75D and S-75S models stand out in their lineup, highlighting excellence in performance and versatility. Designed for both professional welders and industrial applications, these power sources are equipped to handle a variety of welding processes, from MIG to Flux-Core welding.

The Miller Electric S-75D is characterized by its robust construction and advanced technologies. One of its main features is the Auto-Set function, which simplifies the setup process by automatically adjusting the parameters based on the material thickness and wire size. This ensures optimal welding performance, providing welders with confidence in their work. Additionally, the S-75D is equipped with a powerful inverter design, offering increased efficiency and portability. Weighing significantly less than traditional transformer-based units, the S-75D allows for easier transportation to job sites without compromising on power.

On the other hand, the S-75S model incorporates several user-centric enhancements. With a focus on operational ease, it includes a large, intuitive digital display that provides real-time feedback on welding parameters. This feature allows for quick adjustments, ensuring that welders can maintain control over their projects. Furthermore, the S-75S boasts a duty cycle of up to 60%, making it ideal for heavy industrial applications where continuous operation is critical.

Both models share several key technologies that enhance their performance. The Wind Tunnel Technology, for instance, provides superior cooling capabilities, protecting internal components from dust and debris, which prolongs the life of the machine. Additionally, the Power Feed system supports large spools of wire, reducing the frequency of spool changes during long projects.

In terms of characteristics, the S-75D and S-75S are designed with durability in mind. They feature rugged chassis construction and high-quality components that withstand harsh working environments. Furthermore, both machines are equipped to operate in various settings, including fabrication shops, construction sites, and maintenance applications.

In summary, the Miller Electric S-75D and S-75S models represent the pinnacle of welding equipment innovation. With features like Auto-Set, robust duty cycles, intuitive displays, and advanced cooling technologies, they are engineered to meet the demands of skilled welders who seek efficiency, reliability, and high-quality performance in their work. These power sources are ideal for tackling complex welding tasks while ensuring user-friendly operation and durability in any environment.