Simer Pumps 3997 owner manual Read and Follow Safety Instructions

Safety 2

READ AND FOLLOW

SAFETY INSTRUCTIONS!

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for one of the following signal words and be alert to the potential for personal injury!

DANGER warns about hazards that will cause serious personal injury, death or major property damage if ignored.

WARNING warns about hazards that can cause serious personal injury, death or major property damage if ignored.

CAUTION warns about hazards that will or can cause minor personal injury or property damage if ignored.

The word NOTICE indicates special instructions which are important but not related to hazards.

Electrically powered sump pumps normally give many years of trouble-free service when correctly installed, maintained, and used. However, unusual circumstances (interruption of power to the pump, dirt/debris in the sump, flooding that exceeds the pump’s capacity, electri- cal or mechanical failure in the pump, etc.) may prevent your pump from functioning normally. To prevent possi- ble water damage due to flooding, consult your dealer about installing a secondary sump pump, a DC backup sump pump, and/or a high water alarm. See the “Troubleshooting Chart” in this manual for information about common sump pump problems and remedies. For more information, see your retailer, call Simer customer service at 1-800-468-7867 or visit our website at www.simerpump.com.

Hazardous Voltage. Risk of electrical shock. Shock can cause serious injury or death. Failure to follow the warnings below can result in fatal electric shock.

1.If your basement has water or moisture on the floor, do not walk on the wet area until all the power has been turned off. If the shut-off box is in the base- ment, call the electric company or the hydro authori- ty to shut off the service to the house, or call your local fire department for instructions. Do not handle the pump or pump motor with wet hands or when standing on wet or damp surfaces.

2.The pump is equipped with a three-prong, grounding cord and plug. Plug into a properly grounded, grounding-type receptacle only. Where a 2-prong wall receptacle encountered, it must be replaced

with a properly grounded 3-prong receptacle installed in accordance with codes and ordinances that apply. Do not modify the cord or plug. Plug into a 115V, 15 amp individual branch circuit only. Make certain your power source conforms to the require- ments of your equipment.

3.All wiring should be performed by a qualified electrician.

4.Protect the electrical cord from sharp objects, hot surfaces, oils, and chemicals.

Hazardous pressure. Risk of explosion and personal injury. Failure to follow the warnings below can result in personal injury.

5.Secure the discharge line before starting pump. An unsecured discharge line will whip, possible causing personal injury and/or property damage.

6.Know the pump application, limitations and poten- tial hazards.

7.Wear safety glasses at all times when working with pump.

8.Keep the work area clean, uncluttered and properly lighted - replace all unused tools and equipment.

9.Keep visitors at a safe distance from working area.

10.Make the workshop child-proof - with padlocks, master switches, and by removing starter keys.

11.Release all pressure within the system before servic- ing any component.

12.Provide a means of pressure relief for pumps whose discharge line can be shut-off or obstructed.

13.Check hoses for weak or worn condition before each use, making certain that all connections are secure.

Burn Hazard. Can cause personal injury. Do not touch an operating motor. Modern motors can operate at high temperatures. To do so can cause personal injury.

Risk of flooding. Can cause personal injury or property damage. If a flexible discharge hose is used, pump may move around in sump when motor starts. If it moves far enough so that the switch hits the side of sump, the switch may stick and pre- vent the pump from starting. Make sure the pump is secured so it cannot move around in the sump.

14.Periodically inspect the sump, pump and system components. Keep the sump free of debris and for- eign objects. Perform routine maintenance as required.

15.Drain all the water from the system before servicing.

For parts or assistance, call Simer Customer Service at 1-800-468-7867 /1-800-546-7867