Miller Electric TM-353E manual EMF Information, About Pacemakers

Page 6

FALLING EQUIPMENT can cause serious personal injury and equipment damage.

1.Use lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

2.Use equipment of adequate capacity to lift unit.

MAGNETIC FIELDS FROM HIGH CURRENTS can affect pacemaker operation.

1.Pacemaker wearers keep away from servicing areas until consulting your doctor.

MOVING PARTS can cause injury.

1.Keep away from moving parts such as fans.

2.Keep all doors, panels, covers, and guards closed and securely in place.

MOVING PARTS can cause injury.

1.Keep away from moving parts.

2.Keep away from pinch points such as drive rolls.

OVERUSE can cause OVERHEATED EQUIPMENT.

1.Allow cooling period.

2.Reduce current or reduce duty cycle before starting to weld again.

3.Follow rated duty cycle.

READ INSTRUCTIONS.

1.Use MILLER Testing Booklet (Part No. 150 853) when servicing this unit.

2.Consult the Owner’s Manual for welding safety precautions.

3.Use only genuine MILLER replacement parts.

1-3. EMF Information

Considerations About Welding And The Effects Of Low Frequency Electric And Magnetic Fields

The following is a quotation from the General Conclusions Section of the U.S. Congress, Office of Technology Assessment, Biological Effects of Power Frequency Electric & Magnetic Fields – Background Paper, OTA-BP-E-53 (Washington, DC: U.S. Government Printing Office, May 1989): “. . . there is now a very large volume of scientific findings based on experiments at the cellular level and from studies with animals and people which clearly establish that low frequency magnetic fields can interact with, and produce changes in, biological systems. While most of this work is of very high quality, the results are complex. Current scientific understanding does not yet allow us to interpret the evidence in a single coherent framework. Even more frustrating, it does not yet allow us to draw definite conclusions about questions of possible risk or to offer clear science-based advice on strategies to minimize or avoid potential risks.”

To reduce magnetic fields in the workplace, use the following procedures:

1.Keep cables close together by twisting or taping them.

2.Arrange cables to one side and away from the operator.

3.Do not coil or drape cables around the body.

4.Keep welding power source and cables as far away as practical.

5.Connect work clamp to workpiece as close to the weld as possible.

About Pacemakers:

The above procedures are also recommended for pacemaker wearers. Consult your doctor for complete information.

TM-353 Page 2

Syncrowave 250

Page 5 Page 7
Image 6
Page 5 Page 7
Contents SyncrowaveR Table of Contents Declaration of Conformity For European Community CE Products Page Marks a special safety message Safety Precautions for ServicingSymbol Usage Servicing HazardsEMF Information About Pacemakers+ + + DefinitionsISO/IEC Rating Label For CE ProductsSymbols And Definitions Some symbols are found only on CE productsVolt-Ampere Curves InstallationSpecifications 220 230 260 380 415 460Duty Cycle And Overheating 60% Duty Cycle At 200 AmperesOverheating Dimensions And Weights Selecting a LocationMovement Location And Airflow Weld Output Terminals And Selecting Cable Sizes Be careful when placing or moving unit over uneven surfacesTipping ARC Welding can cause Electromagnetic InterferenceVolts AC Duplex Receptacle And Shielding Gas Connections Turn Off power before connecting to receptacleRemote 14 Receptacle SocketElectrical Service Guide All values calculated at 60% duty cyclePlacing Jumper Links And Connecting Input Power Check label inside your unit- only one label is on unitOperation ControlsOutput Selector Switch MetersCrater Time Controls Spot Time ControlsApplication Setting Output Waveforms AC Balance ControlBalance Control AC Gtaw Amperage Adjustment Controls Output Contactor Control SwitchArc Controls Postflow Time ControlFor AC And DC Smaw Welding High Frequency Controls Preflow Time Control OptionalTheory of Operation SCRHD1 Troubleshooting Troubleshooting TableNecessary parts Dition of contacts. Replace CR5 if necessary Contacts. Replace CR2 if necessary Troubleshooting Circuit Diagram For Welding Power Source V24 See -1 forHD1 location D, EWaveforms For Section GndAC Output, 100 Amperes, 24 Volts AC Re- sistive Load Control Board PC1 Testing Information Use With Section Control Board PC1 Test Point Values Reference for gate pulse to SCR4 RC54 Not usedReceptacle Pin Value Remote Board PC2 Testing Information Use With Section RC3 Meter Calibration Input Voltage Labels And Connections Months MaintenanceRoutine Maintenance Circuit Breaker CB1Adjusting Spark Gaps Turn Off power before adjusting spark gapsFuses F1 And F2 Welding Processes Using HF Sources Of HF Radiation From Incorrect InstallationHigh Frequency HF Correct Installation Electrical Diagrams Model Serial Or Style Number Circuit Diagram Wiring DiagramSC-114 SC-120 SC-121 SC-124 SC-124 785-B SC-132 697-A SC-137 SC-135 SC-142 SC-148 SC-154 649-C SC-178 SC-179 303-A SC-181 109-E SC-188 161-A Syncrowave TM-353 TM-353 SD-188 162-A TM-353 SD-187 644 1 TM-353 SD-187 644 2 SA-121 SA-044 725-C TM-353 Description Parts List Main AssemblyPLG51 114 BASE, Prior to KE727074 170 Panel, Front w/Components Panel, Front w/ Components Rectifier, Si Diode -1 Item Panel, Mtg Components -1 Item Control Panel, Lower Front 126 Capacitor ASSEMBLY, Eff w/JK537589 thru JK690986 C14 124 COIL, HF coupling Eff w/JK572898 thru KF959378 174 Optional Equipment Page Miller
Top Page Image Contents