Miller Electric TM-353E manual Remote Board PC2 Testing Information Use With Section

Page 37

6-6. Remote Board PC2 Testing Information (Use With Section 6-7)

1

Y Disable high frequency by placing High Frequency switch S2 in Off position before testing unit.

Be sure plugs are secure before testing. See Section 6-7 for specific values during testing.

1 Remote 14 Filter Board PC2

2 Remote 14 receptacle RC1

See Section 3-8 for information.

3 Receptacle RC2

4 Receptacle RC3

4

3

2

Test Equipment Needed:

ST-157 960-B / ST-800 344-A

Syncrowave 250

TM-353 Page 33

Image 37

Contents SyncrowaveR Table of Contents Declaration of Conformity For European Community CE Products Page Symbol Usage Safety Precautions for ServicingMarks a special safety message Servicing HazardsAbout Pacemakers EMF InformationDefinitions + + +Rating Label For CE Products ISO/IECSome symbols are found only on CE products Symbols And DefinitionsSpecifications InstallationVolt-Ampere Curves 220 230 260 380 415 46060% Duty Cycle At 200 Amperes Duty Cycle And OverheatingOverheating Selecting a Location Dimensions And WeightsMovement Location And Airflow Tipping Be careful when placing or moving unit over uneven surfacesWeld Output Terminals And Selecting Cable Sizes ARC Welding can cause Electromagnetic InterferenceRemote 14 Receptacle Turn Off power before connecting to receptacleVolts AC Duplex Receptacle And Shielding Gas Connections SocketAll values calculated at 60% duty cycle Electrical Service GuideCheck label inside your unit- only one label is on unit Placing Jumper Links And Connecting Input PowerControls OperationMeters Output Selector SwitchSpot Time Controls Crater Time ControlsApplication AC Balance Control Setting Output WaveformsBalance Control AC Gtaw Output Contactor Control Switch Amperage Adjustment ControlsPostflow Time Control Arc ControlsFor AC And DC Smaw Welding Preflow Time Control Optional High Frequency ControlsSCR Theory of OperationHD1 Troubleshooting Table TroubleshootingNecessary parts Dition of contacts. Replace CR5 if necessary Contacts. Replace CR2 if necessary Troubleshooting Circuit Diagram For Welding Power Source HD1 location See -1 forV24 D, EGnd Waveforms For SectionAC Output, 100 Amperes, 24 Volts AC Re- sistive Load Control Board PC1 Testing Information Use With Section Reference for gate pulse to SCR4 RC54 Not used Control Board PC1 Test Point ValuesReceptacle Pin Value Remote Board PC2 Testing Information Use With Section RC3 Meter Calibration Input Voltage Labels And Connections Routine Maintenance MaintenanceMonths Circuit Breaker CB1Turn Off power before adjusting spark gaps Adjusting Spark GapsFuses F1 And F2 Sources Of HF Radiation From Incorrect Installation Welding Processes Using HFHigh Frequency HF Correct Installation Model Serial Or Style Number Circuit Diagram Wiring Diagram Electrical DiagramsSC-114 SC-120 SC-121 SC-124 SC-124 785-B SC-132 697-A SC-137 SC-135 SC-142 SC-148 SC-154 649-C SC-178 SC-179 303-A SC-181 109-E SC-188 161-A Syncrowave TM-353 TM-353 SD-188 162-A TM-353 SD-187 644 1 TM-353 SD-187 644 2 SA-121 SA-044 725-C TM-353 Description Main Assembly Parts ListPLG51 114 BASE, Prior to KE727074 170 Panel, Front w/Components Panel, Front w/ Components Rectifier, Si Diode -1 Item Panel, Mtg Components -1 Item Control Panel, Lower Front 126 Capacitor ASSEMBLY, Eff w/JK537589 thru JK690986 C14 124 COIL, HF coupling Eff w/JK572898 thru KF959378 174 Optional Equipment Page Miller