Miller Electric D-75D, D-75S manual Drive rolls can injure fingers, Keep your head out of the fumes

Page 13

SECTION 3 − DEFINITIONS

3-1. Warning Label Definitions

ABC

1

1.1

1.2

1.3

2			2.1			2.2			2.3

3

3.1

3.2

3.3

4	4.1
	+	+ +
5	+	6
	+

S-178 936

A.Warning! Watch Out! There are possible hazards as shown by the symbols.

B.Drive rolls can injure fingers.

C.Welding wire and drive parts are at welding voltage during operation − keep hands and metal objects clear.

1 Electric shock can kill.

1.1Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.

1.2Protect yourself from electric shock by insulating yourself from work and ground.

1.3Disconnect input plug or power before working on machine.

2Breathing welding fumes can be hazardous to your health.

2.1Keep your head out of the fumes.

2.2Use forced ventilation or local exhaust to remove the fumes.

2.3Use ventilating fan to remove fumes.

3Welding sparks can cause explosion or fire.

3.1Keep flammables away from welding. Don’t weld near flammables.

3.2Welding sparks can cause fires. Have a fire extinguisher nearby and have a watch person ready to use it.

3.3Do not weld on drums or any closed containers.

4Arc rays can burn eyes and injure skin.

4.1Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection.

5Become trained and read the instructions before working on the machine or welding.

6Do not remove or paint over (cover) the label.

OM-228 322 Page 9

Image 13

Contents Processes OM-228 322ADescription File MIG GmawFrom Miller to You Table of Contents Directives Decwire6/05Standards Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier Incendie ou une explosion LE Soudage peut provoquer un DES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéDrive rolls can injure fingers Disconnect input plug or power before working on machineKeep your head out of the fumes Weee Label Symbols And DefinitionsRating Label For CE Products Welding Overall Maximum Wire Feed SpecificationsSite Selection RatingEquipment Connection Diagrams Tools Needed 9/16, 5/8 Connection Point a Point B Rear Panel Connections And Rotating Drive AssemblyLeft Side Shown Installing Drive Rolls Wire Type, Size, And Feed Speed Capability TablePin Plug Information Gun Recommendation TableInstalling PD continuous wire guides with PD drive rolls Installing PD Continuous Wire GuidesInstalling wire guides with non- PD old-style drive rolls Installing Non-PD Old Style Wire GuidesRotate guide holder 180 degrees and reinstall Tools Needed 16, 1/8, 5/32Installing gun with Accu-Mate connection Installing Welding GunSecure gun by tightening power clamp knob Installing gun without Accu- Mate connectionWire Slips No Wire SlipEnd Of Liner Run-In Disabled S1-1 Motor Board DIP Switch SettingsManually Adjusted Run-In S1-1 And S1-2 Left Side Motor Control Board PC101 Right Side MotorPC60 Display Board DIP Switch SettingsLeft/Right Select Switch Power SwitchPower Switch Jog/PurgeTrigger Hold Switches Trigger Hold SwitchVoltage Control And Digital Meters Brush Inspection And Replacement Routine MaintenanceDisconnect power before maintaining = Check ~ = Clean = Replace Reference EveryDiagnostics Disconnect power before troubleshooting TroubleshootingTrouble Remedy − Electrical Diagram 204 716-B 22 -2 Main AssemblyPart Description Quantity Control Box 130 Harness Connectors/ReceptaclesDrive Assembly, Wire -1Item Drive Assembly, Wire Left Side Drive Assembly ShownDrive Assembly With Motor Left Side Drive Assembly Shown PD-V Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s