Simer Pumps 3420P, 3410P, 3415P owner manual Operation, Priming the Pump

Page 8

Operation

8

PRIMING THE PUMP

NOTICE: 'Priming' refers to pump expelling all air in the system and beginning to move water from its source out into system. It does not refer only to pouring water into pump (although pouring water in is usually the first step).

NEVER run pump dry. Running pump with- out water may cause pump to overheat, damaging seal and possibly causing burns to

persons handling pump. Fill pump with water before starting.

Step 1. Remove priming plug.

Step 2. Make sure suction and discharge valves and any hoses on discharge side of pump are open.

Step 3. Fill pump and suction pipe with water (Figure 5).

NEVER run pump against closed discharge. To do so can boil water inside pump, causing hazardous pressure in unit, risk of explosion and possibly scalding persons handling pump (Figure 6). Replace priming plug with pressure gauge to monitor pressure so that it is not allowed to exceed maximum pumping pressures accord- ing to performance chart.

P

76

647 1293

Figure 5: Fill Pump Before Starting

Step 4. Replace priming plug, using Teflon tape on thread; tighten plug.

NOTICE: If priming tee and plug have been pro- vided for long horizontal run, be sure to fill suc- tion pipe through this tee and replace plug. (Use Teflon tape on plug.)

Step 5. Start pump; water should be produced in 10 min- utes or less, time depends on depth to water (not more than 20' (6 m)) and length of horizontal run (10' (3 m) of horizontal suction pipe = 1' (30.5 cm) of vertical lift due to friction losses in pipe). If no water is produced within 10 minutes, stop pump, release all pressure, remove priming plug, refill and try again.

1117 0993

Figure 6: Do Not Run Pump With Outlet Shut Off

NOTICE: Open water system faucets before priming pump for the first time.

Remove priming plug.

Step A. Fully open control valve (turn counterclockwise).

Step B. Fill pump and suction pipe with water.

Step C. Replace priming plug, using Teflon tape on plug thread; tighten plug.

To prevent explosion, do the following:

Step A. Be sure discharge (valve, pistol grip hose nozzle, etc.) is open whenever pump is running.

Step B. If pump fails to produce water when attempting to prime, release all pressure, drain pump and refill with cold water after every attempt.

Step C. When priming, monitor pump body and piping temperature. Motor will warm up; this is normal. If pump body or piping begin to feel warm to touch, shut off pump and allow system to cool. Release all pressure in system and refill pump and piping with cold water.

Step D. Make sure discharge pipe and zone size are not too small for this pumps performance.

For parts or assistance, call Simer Customer Service at 1-800-468-7867 /1-800-546-7867

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Español Composer le 1 800 Llame alEnglish Pages 2-10 Français Safety Read and Follow Safety InstructionsElectrical Safety General SafetyTable of Contents Installation Before YOU Install Your PumpWell Pipe Installation Cased WELL/DUG Well InstallationPUMP/PIPING Installation Driven Point InstallationHorizontal Piping From Well to Pump Discharge Pipe SizesMotor Switch Settings ElectricalRemove Motor END Cover Selecting Voltage with Dial Type Voltage SelectorWiring ConnectionsOperation Priming the PumpTroubleshooting Performance Chart / GpmlpmRepair Parts Part NamesSécurité ’alimentation électriqueInstallation 13,14 Électricité 15,16 Fonctionnement 17,18 Table des matièresInstallation Puits CUVELÉ/CREUSÉ Vant D’INSTALLER LA PompeInstallation DE LA Tuyauterie DU Puits Application DE LA Pompe D’ARROSAGE Tuyauterie Horizontale Entre LE Puits ET LA PompeCalibre DU Tuyau DE Refoulement Électricité Réglages DU MoteurCâblage Fonctionnement Amorçage DE LA PompeDiagnostic des pannes Table des rendements / GpmlpmPièces de rechange Nom des pièces3410P 3415P 3420P 2 ch Désignation 115V/230V Réf Des pièces 60 Hz/1 PhSeguridad LEA Y Siga LAS Instrucciones DE SeguridadSeguridad Electrica Seguridad GeneralIndice de Contenido Instalación 22,23 Electricidad 24,25 Operación 26,27Instalación DEL Tubo EN EL Pozo InstalaciónAntes DE Instalar LA Bomba Instalación DE LA Bomba Y Tuberías Instalación EN Pozos CON Tubería HincadaTubería Horizontal DEL Pozo a LA Bomba Tamaños DE LOS Tubos DE DescargaConfiguraciones DEL Interruptor DEL Motor Saque LA Tapa DEL MotorCableado Conecte el motor a tierra antes de conectarlo al suminOperación Cebado DE LA BombaSolución de Problemas Cuadro de funcionamiento / GpmlpmRefacciones Nombres de las Piezas3410P 3415P 3420P 2 HP Nde Descripción 115V/230V De las Piezas 60 Hz/1 Ph

3420P, 3415P, 3410P specifications

Simer Pumps has long been recognized as a leader in the domain of portable pumping solutions, with a strong reputation built on consistent reliability and innovative technologies. Among their well-regarded offerings are the Simer Pumps 3420P, 3410P, and 3415P models, each designed to meet diverse pumping needs across various applications.

Beginning with the Simer Pumps 3420P, this model is engineered for high efficiency and robust performance in both residential and light commercial settings. One of its standout features is a powerful motor that delivers excellent flow rates, making it ideal for tasks such as dewatering, draining pools, and managing flooded basements. The 3420P also includes a durable thermoplastic construction, ensuring resistance to corrosion and long service life. Additionally, its built-in thermal overload protection prevents overheating, allowing users to operate the pump with peace of mind.

Next, the Simer Pumps 3410P has earned accolades for its user-friendly design and versatility. This pump is particularly suited for applications such as lawn irrigation and general water transfer. The 3410P features an adjustable flow rate, allowing users to customize operation according to specific needs. A unique feature of this model is its lightweight construction, making it easy to transport and set up in different locations. Its compact design does not compromise its capacity, ensuring efficient operation regardless of the task at hand.

Finally, the Simer Pumps 3415P exemplifies reliability and innovation, perfect for demanding applications. This model is designed to tackle tougher jobs and handle larger volumes of water with ease. It features an integrated float switch that automates operation, meaning it will activate when water levels rise and deactivate once levels return to normal. The 3415P is also equipped with an advanced motor that operates efficiently, even during prolonged use, showcasing Simer's commitment to energy efficiency.

In terms of technological advancements, all three models benefit from Simer’s focus on durability and efficiency. These pumps utilize state-of-the-art materials and manufacturing processes that not only enhance performance but also extend product longevity. Users can expect these pumps to deliver optimum results with minimal maintenance requirements.

In summary, the Simer Pumps 3420P, 3410P, and 3415P offer a variety of features that cater to a range of pumping needs. With their robust construction, efficient operation, and user-friendly designs, these pumps represent an excellent choice for both residential and commercial users looking for reliable water management solutions. Simer Pumps continues to innovate, ensuring they remain a trusted name in the pumping industry.
Top Page Image Contents