Hitachi DH 22PB HOW to USE, Selecting the driver bit, Confirm the direction of bit rotation Fig

Page 12

English

CAUTION:

◯The dust cup and dust collector (B) are for exclusive use of concrete drilling work. Do not use them for wood or metal drilling work.

◯Insert dust collector (B) completely into the chuck part of the main unit.

◯When turning the rotary hammer on while dust collector (B) is detached from a concrete surface, dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing dust cup on the concrete surface. When using dust collector (B) attached to a drill bit that has more than 7-15/32" (190 mm) of overall length, dust collector (B) cannot touch the concrete surface and will rotate. Therefore please use dust collector (B) by attaching to drill bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length.

◯Dump particles after every two or three holes when drilling.

◯Please replace the drill bit after removing dust collector (B).

8.Selecting the driver bit

Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is employed to drive in the screws.

9.Confirm the direction of bit rotation (Fig. 6)

The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the push button. The L-side of the push button is pushed to turn the bit counterclockwise.

		L	Push
R		L	Button
R
	L	R
		R
		R

Fig. 6

HOW TO USE

CAUTION:

◯To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work.

1. Switch operation

◯The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more. To turn the switch OFF, release the trigger switch to its original position.

◯Pulling the trigger and pushing the stopper, it keeps the switched-on condition which is convenient for continuous running. When switching off, the stopper can be disconnected by pulling the trigger again.

12

Image 12

Contents Manual DE Instrucciones E Instrucciones DE Seguridad Rotary Hammer Marteau rotatif Martillo perforadorContents Meanings of Signal Words Safety English Blades and accessories must be securely mounted to the tool Never touch moving partsNever operate without all guards in place Use right toolKeep motor air vent clean Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Do not wipe plastic parts with solventMake Them Available to Other Users Owners of this Tool Specifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Mounting the drill bit Fig HOW to USE Switch operationSelecting the driver bit Confirm the direction of bit rotation FigRotation + Hammering Rotation onlyWhen driving machine screws Fig When driving wood screws FigHOW to USE the Core BIT for Light Load Using depth gauge FigMounting How to bore Fig Dismounting FigMaintenance and Inspection Accessories Standard AccessoriesSold separately    Drill Bit Taper shank and taper shank adaptorKnock-in anchor Rotation + Hammering Outer wedge type with the female screwInner wedge type with the headless screw Outer wedge type with Female screwLarge hole boring Rotation + Hammering Guide plateCrushing operation Rotation + Hammering Drilling holes rotation only Driving Screws rotation only Phillips Driver BitDust cup, Dust collector B Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSecurite Regles Generale DE SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil correct Manipuler l’outil correctement Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Ne pas essuyer les parties en plastique avec du solvant22. Définitions pour les symboles utilisés sur cet outil Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES Parties4400/min Poids Lbs 2,3 kg Avant L’UTILISATION AvertissementMontage du foret de perçage Fig Utilisation Sélection de la mèche pour visseuseVérifiez la direction de rotation de La mèche Fig Fonctionnement de l’interrupteurRotation + percussion Rotation seulementLors du vissage des vis machine Enfoncement de vis à bois Fig Utilisation de la quenouille FigComment utiliser la mèche queue Conique et le raccord de queueComment Utiliser LA Couronne Pour UNE Charge Legere MontagePerçage Fig Démontage Fig Entretien ET Inspection Accessoires Accessoires StandardVendus séparément Foret de perçage queue conique et raccord de queue conique Cône en a 303619Ancrage de chasse Rotation + percussion Type à cale extérieure avec vis femelleType à cale intérieure avec vis sans tête Perçage de trou à large diamètre Rotation + percussion Plaque centrale de guidageTravail de démolissage Rotation + percussion Perçage de trous rotation seulement Vis d’entraînement rotation uniquement Embout de vissage PhillipsCapuchon anti poussière, Collecteur à poussière B Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad CuidadasNo toque Nunca las piezas móviles Utilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolvente Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones 4400/min Peso Lbs 2,3 kgMontaje Y Operación AplicacionesAntes DE LA Operación AdvertenciaMontaje de la broca Fig PrecauciónComo SE USA Selección de la broca destornilladorConfirmar la dirección de rotación De la broca Fig Operación del conmutadorRotación + golpeteo Rotación solamenteCuando coloque tornillos para Metal Fig Atornillando tornillos para madera FigModo de usar el tope Fig Modo DE Usar LA Barrena Tubular Para Cargas Ligeras MontajeModo de taladrar Fig Desmontaje Fig Mantenimiento E Inspección Accesorios Accesorios Estándar Broca de taladro vástago cónico y adaptador cónico Ancla de martillar Rotación + golpeteo Tipo de reborde exterior con tornillo hembra Tipo de reborde interior con tornillo sin cabezaPlaca guia Trabajo de roturación Rotación + golpeteoPerforación rotación solamente Broca para tornillos PlillipsCopa de polvo, Colector de polvo B Page 626VVC2PS2L Kestrel Road Mississauga on L5T 1Z5