DeWalt D28112, D28402N Assembly and Adjustments, Rotating the Gear Case, Accessories

Page 6

English

FIG. 1

C

D28402

D28402N

F

D28110

D28112

S

I

A

K

B

J

 

 

 

(D28402)

L

L

K

G

H

K

ASSEMBLY AND ADJUSTMENTS

ATTACHING SIDE HANDLE

 

The side handle (E) can be fitted to either

E

side of the gear case in the threaded holes, as shown. Before using the tool, check that the handle is tightened securely. Use a wrench to firmly tighten the side handle.

Rotating the Gear Case

Turn off and unplug tool before making any adjustments or removing or installing accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

1. Remove guard and flanges from tool.

2. Remove the four

corner screws

 

attaching the gear case to motor

 

housing.

90˚

90˚

3.Separating the gear case from motor housing not more than 1/4", rotate the gear case head to desired position.

NOTE: If the gear case and motor housing become separated by more than 1/4", the tool must be serviced and re-assembled by a DEWALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure.

3.Re-install screws to attach the gear case to the motor housing. Tighten screws to 18 in./lbs. torque. Overtightening could cause screws to strip.

Accessories

It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See pages 6–7 for infor- mation on choosing the correct accessories.

5

Image 6
Contents Guide Dutilisation Manual DE Instrucciones General Safety Rules For All Tools Electrical SafetyWork Area Service Additional Specific Safety Instructions for GrindersPersonal Safety Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackComponents Fig Spindle Lock Button Dust Ejection System Spindle not shownRotating the Gear Case Assembly and AdjustmentsAccessories Attaching Side HandleType 27 depressed Center wheel Threaded clamp nut 2 Grinding Wheels Wire WheelsMounting Guard Mounting and Removing Guard D28112, D28402, D28402NSanding Discs 2 Sanding Flap Discs Guards and Flanges SwitchesOperation Mounting and Removing GuardSpindle Lock LOCK-ON Button D28402On button J. The tool will continue to Mounting and Removing Hubbed WheelsBack motion to avoid creating Must be used with included flanges. SeeSurface Grinding with Grinding Wheels Edge Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Very Fine FinishingMounting and Using Wire Brushes and Wire Wheels Mounting Wire CUP Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 Wheels Mounting Closed Type 1 GuardMounting Cutting Wheels Accessories Three Year Limited Warranty MaintenanceCleaning LubricationAddition to the warranty, Dewalt tools are covered by our Year Free ServiceDAY Money Back Guarantee Aire DE Travail Règles de sécurité GénéralitésConserver CES Directives Mesures DE Sécurité ÉlectricitéSécurité Personnelle Utilisation ET Entretien DE L’OUTILDirectives de sécurité supplémentaires pour meuleuses EntretienCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Positionnement du carter d’engrenages Composants figAssemblage ET Réglages Fixation DE LA Poignée LatéraleAccessoires Montage du dispositif de protectionOuvert, tourner le dispositif I dans la Dispositif de Montage ET Démontage DU Dispositif DE Protection D28110La meuleuse avec un dispositif de protection desserré FonctionnementDispositifs de protection et brides Alignées, puis tirer sur le dispositif de protectionBouton DE Verrouillage D28402 InterrupteursInterrupteur À Palette D28402 D28402N Interrupteur Coulissant D28110, D28112Montage DE Meules Sans Moyeu Dispositif DE Verrouillage DE LA BrocheMontage ET Démontage DE Meules À Moyeu Poser la bride tournante sur collet battuMeulage DE Finition Avec DES Meules Meulage DE Bordure Avec DES MeulesFinition DE Surface Avec DES Disques À Lamelles DE Ponçage Utilisation DES Patins DE Ponçage ET D’APPUIMontage DES Patins D’APPUI ET DE Ponçage De la pièce Métalliques ou de brosses métalliques à touretMontage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection Fermé TypeMontage DE Meules DE Coupe EntretienNettoyage Utilisation DES Meules DE CoupeGarantie limitée de trois ans LubrificationRéparations Contrat D’ENTRETIEN Gratuit D’UN ANÁrea DE Trabajo Instrucciones de seguridad generalesConserve Estas Instrucciones Seguridad EléctricaSeguridad Personal MásCalibre del cordón AWG No recomendado USO Y Cuidados DE LA HerramientaServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Como girar la caja de engranajes Componentes FigEnsamblado Y Ajustes AccesoriosInstalación del protector Montaje Y Remoción DEL Protector D28110Operación Protectores y bridasInterruptores Interruptor DE Paleta D28402, D28402NBloqueo DEL EJE Interruptor Deslizante D28110, D28112Botón DE Bloqueo D28402 Montaje Y Remoción DE Discos CON CuboEnsamblado DE Discos SIN Cubo Esmerilado DE Superficies CON Discos Para EsmerilarDe aplicarla a la superficie de trabajo Esmerilado DE Bordes CON Discos Para EsmerilarAcabado DE Superficies CON Discos Para Lijar Mienta hacia adelante y hacia atrásMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de los discos de corte Tipo La sección elevada piloto Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte Piloto en dirección opuesta al discoLubricación MantenimientoLimpieza ReparacionesAÑO DE Servicio Gratuito Garantía limitada por tres añosExcepciones Garantía DE Reembolso DE SU Dinero POR 90 DíasCULIACAN, SIN Especificaciones D28402, D28402N