DeWalt D28402N, D28112 instruction manual Grinding Wheels Wire Wheels, Mounting Guard

Page 7

4-1/2" Grinding Wheels

Wire Wheels

Type 27 guard

backing flange

Type 27 guard

Type 27 hubbed wheel

Type 27 guard

3" wire cup

brush

Type 27 guard

4" wire wheel

English

Type 27 depressed

center wheel

threaded clamp nut

Mounting Guard

MOUNTING AND REMOVING GUARD (D28112, D28402, D28402N)

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other acces- sories running over rated accessory speed may burst and cause injury. Threaded accessories must have a 5/8"-11 hub. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 6–7 of this man- ual. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

CAUTION: Guards must be used with all grinding wheels, sanding flap discs, wire brushes, and wire wheels. The tool may be used without a guard only when sanding with conventional sanding discs. Some DEWALT models are provided with a guard intended for use with depressed center wheels (Type 27) and hubbed grinding wheels (Type 27). The same guard is designed for use with sanding flap discs (Type 27 and 29) and wire brushes. Grinding and cutting with wheels other than Type 27 and 29 require different accessory guards not included with tool. Mounting instructions for these accessory guards are included in the acces- sory package.

6

Image 7
Contents Guide Dutilisation Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Tool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolSpindle Lock Button Dust Ejection System Spindle not shown Components FigAttaching Side Handle Assembly and AdjustmentsAccessories Rotating the Gear CaseMounting and Removing Guard D28112, D28402, D28402N 2 Grinding Wheels Wire WheelsMounting Guard Type 27 depressed Center wheel Threaded clamp nutSanding Discs 2 Sanding Flap Discs Mounting and Removing Guard SwitchesOperation Guards and FlangesMounting and Removing Hubbed Wheels LOCK-ON Button D28402On button J. The tool will continue to Spindle LockEdge Grinding with Grinding Wheels Must be used with included flanges. SeeSurface Grinding with Grinding Wheels Back motion to avoid creatingVery Fine Finishing Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Mounting Sanding Backing PadsMounting Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsMounting Cutting Wheels Lubrication MaintenanceCleaning Accessories Three Year Limited WarrantyYear Free Service Addition to the warranty, Dewalt tools are covered by ourDAY Money Back Guarantee Mesures DE Sécurité Électricité Règles de sécurité GénéralitésConserver CES Directives Aire DE TravailUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleEntretien Directives de sécurité supplémentaires pour meuleusesCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Fixation DE LA Poignée Latérale Composants figAssemblage ET Réglages Positionnement du carter d’engrenagesMontage du dispositif de protection AccessoiresOuvert, tourner le dispositif I dans la Montage ET Démontage DU Dispositif DE Protection D28110 Dispositif deAlignées, puis tirer sur le dispositif de protection FonctionnementDispositifs de protection et brides La meuleuse avec un dispositif de protection desserréInterrupteur Coulissant D28110, D28112 InterrupteursInterrupteur À Palette D28402 D28402N Bouton DE Verrouillage D28402Poser la bride tournante sur collet battu Dispositif DE Verrouillage DE LA BrocheMontage ET Démontage DE Meules À Moyeu Montage DE Meules Sans MoyeuMeulage DE Bordure Avec DES Meules Meulage DE Finition Avec DES MeulesUtilisation DES Patins DE Ponçage ET D’APPUI Finition DE Surface Avec DES Disques À Lamelles DE PonçageMontage DES Patins D’APPUI ET DE Ponçage Métalliques ou de brosses métalliques à touret De la pièceMontage D’UN Dispositif DE Protection Fermé Type Montage et utilisation de meules de coupe typeUtilisation DES Meules DE Coupe EntretienNettoyage Montage DE Meules DE CoupeContrat D’ENTRETIEN Gratuit D’UN AN LubrificationRéparations Garantie limitée de trois ansSeguridad Eléctrica Instrucciones de seguridad generalesConserve Estas Instrucciones Área DE TrabajoUSO Y Cuidados DE LA Herramienta MásCalibre del cordón AWG No recomendado Seguridad PersonalServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Accesorios Componentes FigEnsamblado Y Ajustes Como girar la caja de engranajesMontaje Y Remoción DEL Protector D28110 Instalación del protectorProtectores y bridas OperaciónInterruptor DE Paleta D28402, D28402N InterruptoresMontaje Y Remoción DE Discos CON Cubo Interruptor Deslizante D28110, D28112Botón DE Bloqueo D28402 Bloqueo DEL EJEEsmerilado DE Superficies CON Discos Para Esmerilar Ensamblado DE Discos SIN CuboMienta hacia adelante y hacia atrás Esmerilado DE Bordes CON Discos Para EsmerilarAcabado DE Superficies CON Discos Para Lijar De aplicarla a la superficie de trabajoUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje y uso de los discos de corte Tipo Piloto en dirección opuesta al disco Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte La sección elevada pilotoReparaciones MantenimientoLimpieza LubricaciónGarantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoCULIACAN, SIN Especificaciones D28402, D28402N