Cisco Systems CSACS1121K9 manual Safety Information, FCC Safety Compliance Statement

Page 28

Chapter 2 Installing the Access Point

Safety Information

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point.

FCC Safety Compliance Statement

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.

General Safety Guidelines

•Do not touch or move antenna(s) while the unit is transmitting or receiving.

•Do not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.

•The use of wireless devices in hazardous locations is limited to the constraints posed by the local codes, the national codes, and the safety directors of such environments.

Warnings

Translated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A, “Translated Safety Warnings” for instructions.

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245B

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning Read the installation instructions before you connect the system to its power source. Statement 1004

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20 A.. Statement 1005

Cisco Aironet 1100 Series Access Point Hardware Installation Guide

2-2	OL-4309-07

Image 28

Contents Corporate Headquarters Page N T E N T S Deploying the Access Points on the Wireless Network Finding the Software Version Chinese Translation B-7 Preface AudiencePurpose OrganizationConventions ViiiPreface Conventions Related Publications Obtaining DocumentationDocumentation Feedback Cisco Product Security OverviewCisco.com Product Documentation DVD Ordering DocumentationReporting Security Problems in Cisco Products Product Alerts and Field NoticesObtaining Technical Assistance Cisco Support WebsiteLocating the Product Serial Number Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Xvi Autonomous Access Points Lightweight Access PointsOverview Product TerminologyOverview Single Radio Operation Hardware FeaturesEthernet Port Power Sources LEDsAnti-Theft Features Network Examples with Autonomous Access PointsUL 2043 Certification Root Unit on a Wired LAN Access pointRepeater Unit that Extends Wireless Range Access Point as RepeaterCentral Unit in an All-Wireless Network Workgroup Bridge Configuration Network Example with Lightweight Access Points Typical Layer 3 Network Configuration ExampleOL-4309-07 Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Basic Installation Guidelines Unpacking the Access PointPackage Contents Access Point Layout and Connectors 1shows the access point layout and connectorsDeploying the Access Points on the Wireless Network Controller Discovery Process for Lightweight Access PointsOL-4309-07 Connecting the Ethernet and Power Cables Access Point Power OptionsConnecting to an Ethernet Network with Local Power Powering Up the Access Point OL-4309-07 Mounting Instructions Overview Mounting Method Materials Required KitMounting on a Horizontal or Vertical Surface Mounting BracketMounting on a Suspended Ceiling Suspended Ceiling Mounting Bracket PartsAccess Point Mounting Slots Mounting Above a Suspended Ceiling Remove a ceiling tile adjacent to the mounting locationUsing the Security Hasp Adapter Security Hasp AdapterMounting on a Cubical Wall Partition Security Hasp with PadlockUsing the Desktop Holster Cubicle Wall BracketDesktop Holster Using the Cable Lock Feature Kensington LockOL-4309-07 GHz Radio Upgrade for Autonomous Access Points Upgrade Overview Unpacking the RadioRemoving the Back Cover Go to the Removing a 2.4-GHz Radio sectionRemoving a 2.4-GHz Radio Radio Card and Antenna CardInstalling a 2.4-GHz Radio Connector pinsInserting Radio Card in Mini-PCI Connector Go to the Replacing the Back Cover section on Replacing the Back Cover Product compliance label Back coverFinding the Software Version OL-4309-07 Troubleshooting Autonomous Access Points Checking the Autonomous Access Point LEDs Ethernet Status RadioLED Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Enabling the Radio Interfaces Security SettingsWEP Keys Running the Carrier Busy Test Resetting to the Default Configuration Running the Ping or Link TestUsing the Mode Button Using the Web Browser InterfaceReloading the Access Point Image Web Browser Interface Browser Http InterfaceObtaining the Access Point Image File Obtaining the Tftp Server SoftwareOL-4309-07 Troubleshooting Lightweight Access Points Guidelines for Using 1100 Series Lightweight Access Points Using Dhcp OptionChecking the Lightweight Access Point LEDs Access Points LEDsMessage Ethernet Status Radio Type Returning the Access Point to Autonomous Mode Enabled see the Mode Button Setting section onObtaining the Autonomous Access Point Image File Mode Button SettingObtaining the Tftp Server Software OL-4309-07 Translated Safety Warnings OL-4309-07 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry-Canada Canadian Compliance StatementOL-4309-07 EMC Declaration of Conformity for RF Exposure Japanese TranslationAll Access Points English TranslationOperation of Cisco Aironet Access Points in Brazil Access Point ModelsDeclaration of Conformity Statements Portuguese TranslationOL-4309-07 Page OL-4309-07 Page OL-4309-07 Access Point Specifications Category SpecificationsRadio GHz Radio To UL 2043 and they should not be placed in a building’s Category Specifications Channels and Maximum Power Levels OL-4309-07 Priming Lightweight Access Points Prior to Deployment OL-4309-07 Page Access Points Lightweight Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 Series Access Points Quotation marks must be includedType + Length + Value OL-4309-07 O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2