Cisco Systems CSACS1121K9 Obtaining the Autonomous Access Point Image File, Mode Button Setting

Page 76

Chapter 6 Troubleshooting Lightweight Access Points

Obtaining the Autonomous Access Point Image File

Step 6 Press and hold the MODE button while you reconnect power to the access point.

Step 7 Hold the MODE button until the Radio LED turns red (approximately 20 to 30 seconds) and then release.

Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.

Step 9 After the access point reboots, reconfigure it using the access point GUI or the CLI. For additional information refer to the Cisco Aironet 1100 Series Access Point Hardware Installation Guide available at this URL:

http://www.cisco.com/en/US/products/hw/wireless/tsd_products_support_category_home.html

To browse to the 1100 series access point documentation, click Cisco Aironet 1100 Series listed under “Wireless LAN Access.”

MODE Button Setting

The lightweight access point MODE button is configured from your controller. Use these controller CLI commands to view and configure the MODE button:

1)config ap rst-button enable <access-point-name>/all

2)config ap rst-button disable <access-point-name>/all

3)show ap config general <access-point-name>

(Where access-point-nameis the name that identifies the access point on the ocntroller.)

Obtaining the Autonomous Access Point Image File

The autonomous access point image file can be obtained from the Cisco.com software center using these steps:

 

 

 

Note

To download software from the Cisco.com software center, you must be a registered user. You can

 

 

 

 

register from the main Cisco.com web page at this URL: http://cisco.com.

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 1

Use your Internet browser to access the Cisco Software Center at the following URL:

 

 

 

 

http://www.cisco.com/cisco/software/navigator.html

 

 

 

Step 2

Click Wireless LAN Access > Aironet Access Points > Cisco Aironet 1100 Series.

 

 

 

Step 3

Click Cisco Aironet 1100 Access Point.

 

 

 

Step 4

On the Enter Network Password window, enter your Cisco.com username and password and click OK.

 

 

 

Step 5

Click IOS.

 

 

 

Step 6

Choose the Cisco IOS release desired, such as 12.3.11.JA.

 

 

 

Step 7

Click WIRELESS LAN for an access point image file, such as c1100-k9w7-tar.123-11.JA.tar.

 

 

 

Step 8

On the Enter Network Password window, enter your Cisco.com username and password and click OK.

 

 

 

Step 9

On the Security Information window, click Yes to display non-secure items.

 

 

 

Cisco Aironet 1100 Series Access Point Hardware Installation Guide

 

 

 

 

6-6

 

 

OL-4309-07

 

 

 

 

 

Page 75 Page 77
Image 76
Page 75 Page 77
Contents Corporate Headquarters Page N T E N T S Deploying the Access Points on the Wireless Network Finding the Software Version Chinese Translation B-7 Preface AudiencePurpose OrganizationConventions ViiiPreface Conventions Related Publications Obtaining DocumentationDocumentation Feedback Cisco Product Security OverviewCisco.com Product Documentation DVD Ordering DocumentationReporting Security Problems in Cisco Products Product Alerts and Field NoticesObtaining Technical Assistance Cisco Support WebsiteLocating the Product Serial Number Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Xvi Autonomous Access Points Lightweight Access PointsOverview Product TerminologyOverview Single Radio Operation Hardware FeaturesEthernet Port Power Sources LEDsAnti-Theft Features Network Examples with Autonomous Access PointsUL 2043 Certification Root Unit on a Wired LAN Access pointRepeater Unit that Extends Wireless Range Access Point as RepeaterCentral Unit in an All-Wireless Network Workgroup Bridge ConfigurationNetwork Example with Lightweight Access Points Typical Layer 3 Network Configuration ExampleOL-4309-07 Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Basic Installation Guidelines Unpacking the Access PointPackage Contents Access Point Layout and Connectors 1shows the access point layout and connectorsDeploying the Access Points on the Wireless Network Controller Discovery Process for Lightweight Access PointsOL-4309-07 Connecting the Ethernet and Power Cables Access Point Power OptionsConnecting to an Ethernet Network with Local Power Powering Up the Access Point OL-4309-07 Mounting Instructions Overview Mounting Method Materials Required KitMounting on a Horizontal or Vertical Surface Mounting BracketMounting on a Suspended Ceiling Suspended Ceiling Mounting Bracket PartsAccess Point Mounting Slots Mounting Above a Suspended Ceiling Remove a ceiling tile adjacent to the mounting locationUsing the Security Hasp Adapter Security Hasp AdapterMounting on a Cubical Wall Partition Security Hasp with PadlockUsing the Desktop Holster Cubicle Wall BracketDesktop Holster Using the Cable Lock Feature Kensington LockOL-4309-07 GHz Radio Upgrade for Autonomous Access Points Upgrade Overview Unpacking the RadioRemoving the Back Cover Go to the Removing a 2.4-GHz Radio sectionRemoving a 2.4-GHz Radio Radio Card and Antenna CardInstalling a 2.4-GHz Radio Connector pinsInserting Radio Card in Mini-PCI Connector Go to the Replacing the Back Cover section on Replacing the Back Cover Product compliance label Back coverFinding the Software Version OL-4309-07 Troubleshooting Autonomous Access Points Checking the Autonomous Access Point LEDs Ethernet Status RadioLED Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Enabling the Radio Interfaces Security SettingsWEP Keys Running the Carrier Busy Test Resetting to the Default Configuration Running the Ping or Link TestUsing the Mode Button Using the Web Browser InterfaceReloading the Access Point Image Web Browser Interface Browser Http InterfaceObtaining the Access Point Image File Obtaining the Tftp Server SoftwareOL-4309-07 Troubleshooting Lightweight Access Points Guidelines for Using 1100 Series Lightweight Access Points Using Dhcp OptionChecking the Lightweight Access Point LEDs Access Points LEDsMessage Ethernet Status Radio Type Returning the Access Point to Autonomous Mode Enabled see the Mode Button Setting section onObtaining the Autonomous Access Point Image File Mode Button SettingObtaining the Tftp Server Software OL-4309-07 Translated Safety Warnings OL-4309-07 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry-Canada Canadian Compliance StatementOL-4309-07 EMC Declaration of Conformity for RF Exposure Japanese TranslationAll Access Points English TranslationOperation of Cisco Aironet Access Points in Brazil Access Point ModelsDeclaration of Conformity Statements Portuguese TranslationOL-4309-07 Page OL-4309-07 Page OL-4309-07 Access Point Specifications Category SpecificationsRadio GHz Radio To UL 2043 and they should not be placed in a building’s Category Specifications Channels and Maximum Power Levels OL-4309-07 Priming Lightweight Access Points Prior to Deployment OL-4309-07 Page Access Points Lightweight Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 Series Access Points Quotation marks must be includedType + Length + Value OL-4309-07 O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2

CSACS1121K9 specifications

Cisco Systems CSACS1121K9 is a part of Cisco's comprehensive suite of security solutions tailored for identity and access management. This device, recognized for its reliability and functionality, plays a crucial role in ensuring that organizations can efficiently manage user access across their networks.

One of the main features of the CSACS1121K9 is its centralized user authentication capabilities. This device simplifies the process of validating user identities, allowing administrators to manage credentials for a variety of access methods, including web-based authentication, RADIUS, and TACACS+. This flexibility plays a significant role in diverse environments where different protocols may be required for various devices or applications.

The CSACS1121K9 is built on the robust Cisco Secure Access Control Server (ACS) platform. This platform supports a wide range of security policies, making it versatile enough for different organizational needs. With its capability to integrate seamlessly with other Cisco solutions and third-party platforms, the device enhances the overall security posture of an organization.

In terms of scalability, the CSACS1121K9 can support a substantial number of users and devices. This scalability ensures that as organizations grow, their access management system can scale proportionately without performance degradation. The ability to handle thousands of simultaneous authentication requests makes it suitable for both small companies and large enterprises.

Another significant characteristic of the CSACS1121K9 is its support for advanced visibility and reporting. Administrators can track authentication attempts, policy enforcement, and other critical events in real time. This level of monitoring is essential for compliance audits and helps organizations quickly react to potential security threats.

Moreover, the CSACS1121K9 includes capabilities for implementing role-based access control (RBAC). This feature allows organizations to define specific access rights based on user roles, which enhances security while facilitating efficient operations.

In conclusion, the Cisco Systems CSACS1121K9 is a powerful tool for organizations seeking to enhance their identity and access management frameworks. With its centralized user authentication, scalability, advanced reporting capabilities, and support for RBAC, it provides a robust solution that can adapt to the evolving security demands of modern networks. Whether deployed in a small business environment or within large enterprises, the CSACS1121K9 stands out for its comprehensive feature set and ability to integrate into existing security infrastructures.
Top Page Image Contents