Cisco Systems CSACS1121K9 manual

Page 103

Appendix E Priming Lightweight Access Points Prior to Deployment

Step 5 If the operating system download is successful, the access point reboots. Normal operation is indicated when the radio LED is blinking to indicate radio activity.

Step 6 Use controller CLI, controller GUI, or Cisco WCS to configure the lightweight access point with primary, secondary, and tertiary controller names.

Step 7 If the lightweight access point is in a Controller Mobility Group, use the controller CLI, controller GUI, or Cisco WCS to configure the Controller Mobility Group name.

Step 8 Use controller CLI, controller GUI, or Cisco WCS to configure the lightweight access point-specific 802.11a, 802.11b, and 802.11g network settings.

Step 9 If the configuration priming was successful, the radio LED is blinking to indicate normal operation. Step 10 Repeat Steps 4 to 9 for each lightweight access point.

When you successfully complete the configuration priming of all your lightweight access points, ensure Master setting is disabled on your controller. You can begin deploying the access points to their final destinations (refer to the “Deploying the Access Points on the Wireless Network” section on page 2-5).

Cisco Aironet 1100 Series Access Point Hardware Installation Guide

	OL-4309-07	E-3

Image 103

Contents Corporate Headquarters Page N T E N T S Deploying the Access Points on the Wireless Network Finding the Software Version Chinese Translation B-7 Organization PrefaceAudience PurposeViii ConventionsPreface Conventions Obtaining Documentation Related PublicationsProduct Documentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview Cisco.comProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsCisco Support Website Obtaining Technical AssistanceLocating the Product Serial Number Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Xvi Product Terminology Autonomous Access PointsLightweight Access Points OverviewOverview Single Radio Operation Hardware FeaturesEthernet Port LEDs Power SourcesAnti-Theft Features Network Examples with Autonomous Access PointsUL 2043 Certification Access point Root Unit on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeWorkgroup Bridge Configuration Central Unit in an All-Wireless NetworkTypical Layer 3 Network Configuration Example Network Example with Lightweight Access PointsOL-4309-07 Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Basic Installation Guidelines Unpacking the Access PointPackage Contents 1shows the access point layout and connectors Access Point Layout and ConnectorsController Discovery Process for Lightweight Access Points Deploying the Access Points on the Wireless NetworkOL-4309-07 Access Point Power Options Connecting the Ethernet and Power CablesConnecting to an Ethernet Network with Local Power Powering Up the Access Point OL-4309-07 Mounting Instructions Mounting Method Materials Required Kit OverviewMounting Bracket Mounting on a Horizontal or Vertical SurfaceSuspended Ceiling Mounting Bracket Parts Mounting on a Suspended CeilingAccess Point Mounting Slots Remove a ceiling tile adjacent to the mounting location Mounting Above a Suspended CeilingSecurity Hasp Adapter Using the Security Hasp AdapterSecurity Hasp with Padlock Mounting on a Cubical Wall PartitionCubicle Wall Bracket Using the Desktop HolsterDesktop Holster Kensington Lock Using the Cable Lock FeatureOL-4309-07 GHz Radio Upgrade for Autonomous Access Points Unpacking the Radio Upgrade OverviewGo to the Removing a 2.4-GHz Radio section Removing the Back CoverRadio Card and Antenna Card Removing a 2.4-GHz RadioConnector pins Installing a 2.4-GHz RadioInserting Radio Card in Mini-PCI Connector Go to the Replacing the Back Cover section on Product compliance label Back cover Replacing the Back CoverFinding the Software Version OL-4309-07 Troubleshooting Autonomous Access Points Ethernet Status Radio Checking the Autonomous Access Point LEDsLED Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Enabling the Radio Interfaces Security SettingsWEP Keys Running the Carrier Busy Test Running the Ping or Link Test Resetting to the Default ConfigurationUsing the Web Browser Interface Using the Mode ButtonReloading the Access Point Image Browser Http Interface Web Browser InterfaceObtaining the Tftp Server Software Obtaining the Access Point Image FileOL-4309-07 Troubleshooting Lightweight Access Points Using Dhcp Option Guidelines for Using 1100 Series Lightweight Access PointsAccess Points LEDs Checking the Lightweight Access Point LEDsMessage Ethernet Status Radio Type Enabled see the Mode Button Setting section on Returning the Access Point to Autonomous ModeMode Button Setting Obtaining the Autonomous Access Point Image FileObtaining the Tftp Server Software OL-4309-07 Translated Safety Warnings OL-4309-07 Declarations of Conformity and Regulatory Information For Home or Office USE Canadian Compliance Statement Vcci Statement for Japan Industry-CanadaOL-4309-07 EMC Japanese Translation Declaration of Conformity for RF ExposureEnglish Translation All Access PointsAccess Point Models Operation of Cisco Aironet Access Points in BrazilPortuguese Translation Declaration of Conformity StatementsOL-4309-07 Page OL-4309-07 Page OL-4309-07 Category Specifications Access Point SpecificationsRadio GHz Radio To UL 2043 and they should not be placed in a building’s Category Specifications Channels and Maximum Power Levels OL-4309-07 Priming Lightweight Access Points Prior to Deployment OL-4309-07 Page Access Points Lightweight Access Point Vendor Class Identifier VCI Quotation marks must be included Configuring Option 43 for 1000 Series Access PointsType + Length + Value OL-4309-07 O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2