Cisco Systems CSACS1121K9 manual Using the Security Hasp Adapter

Page 43

Chapter 3 Mounting Instructions

Using the Security Hasp Adapter

Step 4 Configure the ends of the T-bar box hanger to allow for maximum clearance above the ceiling tile. See the illustration above.

Step 5 Attach the T-rail clips on the each end of the T-bar box hanger to the ceiling grid T-rails. Make sure the clips are securely attached to the T-rails.

Step 6 Connect a drop wire to a building structural element and the hole provided in the bracket mounting clip. This additional support is required in order to comply with the U.S. National Electrical Safety Code.

Step 7 Attach the access point to the access point mounting bracket.

Step 8 Connect the Ethernet cables to the access point.

Note The power module and power injector are not rated for mounting above suspended ceilings. Therefore, you must use the Ethernet cable to supply power.

Step 9 If you need additional security, you can secure the access point to a nearby immovable object using a Kensington lock and security cable.

Step 10 Verify that the access point is operating before replacing the ceiling tile.

Using the Security Hasp Adapter

The security hasp on the wall or ceiling mounting bracket and the security hasp adapter locks the access point to the bracket to make it more secure. After you have installed the access point on the detachable mounting bracket, follow these steps to secure it with a padlock (Master Lock model 120T, 121T or equivalent).

Step 1 Connect the Ethernet cable and power jack.

Step 2 Insert the T-shaped tab on the security hasp adapter into the Kensington lock slot on the access point. See Figure 3-6.

Figure 3-6 Security Hasp Adapter

81177

Cisco Aironet 1100 Series Access Point Hardware Installation Guide

 

OL-4309-07

3-7

 

 

 

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Corporate Headquarters Page N T E N T S Deploying the Access Points on the Wireless Network Finding the Software Version Chinese Translation B-7 Organization PrefaceAudience PurposeViii ConventionsPreface Conventions Obtaining Documentation Related PublicationsProduct Documentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview Cisco.comProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsCisco Support Website Obtaining Technical AssistanceLocating the Product Serial Number Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Xvi Product Terminology Autonomous Access PointsLightweight Access Points OverviewOverview Single Radio Operation Hardware FeaturesEthernet Port LEDs Power SourcesAnti-Theft Features Network Examples with Autonomous Access PointsUL 2043 Certification Access point Root Unit on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeWorkgroup Bridge Configuration Central Unit in an All-Wireless NetworkTypical Layer 3 Network Configuration Example Network Example with Lightweight Access PointsOL-4309-07 Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Basic Installation Guidelines Unpacking the Access PointPackage Contents 1shows the access point layout and connectors Access Point Layout and ConnectorsController Discovery Process for Lightweight Access Points Deploying the Access Points on the Wireless NetworkOL-4309-07 Access Point Power Options Connecting the Ethernet and Power CablesConnecting to an Ethernet Network with Local Power Powering Up the Access Point OL-4309-07 Mounting Instructions Mounting Method Materials Required Kit OverviewMounting Bracket Mounting on a Horizontal or Vertical SurfaceSuspended Ceiling Mounting Bracket Parts Mounting on a Suspended CeilingAccess Point Mounting Slots Remove a ceiling tile adjacent to the mounting location Mounting Above a Suspended CeilingSecurity Hasp Adapter Using the Security Hasp AdapterSecurity Hasp with Padlock Mounting on a Cubical Wall PartitionCubicle Wall Bracket Using the Desktop HolsterDesktop Holster Kensington Lock Using the Cable Lock FeatureOL-4309-07 GHz Radio Upgrade for Autonomous Access Points Unpacking the Radio Upgrade OverviewGo to the Removing a 2.4-GHz Radio section Removing the Back CoverRadio Card and Antenna Card Removing a 2.4-GHz RadioConnector pins Installing a 2.4-GHz RadioInserting Radio Card in Mini-PCI Connector Go to the Replacing the Back Cover section on Product compliance label Back cover Replacing the Back CoverFinding the Software Version OL-4309-07 Troubleshooting Autonomous Access Points Ethernet Status Radio Checking the Autonomous Access Point LEDsLED Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Enabling the Radio Interfaces Security SettingsWEP Keys Running the Carrier Busy Test Running the Ping or Link Test Resetting to the Default ConfigurationUsing the Web Browser Interface Using the Mode ButtonReloading the Access Point Image Browser Http Interface Web Browser InterfaceObtaining the Tftp Server Software Obtaining the Access Point Image FileOL-4309-07 Troubleshooting Lightweight Access Points Using Dhcp Option Guidelines for Using 1100 Series Lightweight Access PointsAccess Points LEDs Checking the Lightweight Access Point LEDsMessage Ethernet Status Radio Type Enabled see the Mode Button Setting section on Returning the Access Point to Autonomous ModeMode Button Setting Obtaining the Autonomous Access Point Image FileObtaining the Tftp Server Software OL-4309-07 Translated Safety Warnings OL-4309-07 Declarations of Conformity and Regulatory Information For Home or Office USE Canadian Compliance Statement Vcci Statement for Japan Industry-CanadaOL-4309-07 EMC Japanese Translation Declaration of Conformity for RF ExposureEnglish Translation All Access PointsAccess Point Models Operation of Cisco Aironet Access Points in BrazilPortuguese Translation Declaration of Conformity StatementsOL-4309-07 Page OL-4309-07 Page OL-4309-07 Category Specifications Access Point SpecificationsRadio GHz Radio To UL 2043 and they should not be placed in a building’s Category Specifications Channels and Maximum Power Levels OL-4309-07 Priming Lightweight Access Points Prior to Deployment OL-4309-07 Page Access Points Lightweight Access Point Vendor Class Identifier VCI Quotation marks must be included Configuring Option 43 for 1000 Series Access PointsType + Length + Value OL-4309-07 O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2

CSACS1121K9 specifications

Cisco Systems CSACS1121K9 is a part of Cisco's comprehensive suite of security solutions tailored for identity and access management. This device, recognized for its reliability and functionality, plays a crucial role in ensuring that organizations can efficiently manage user access across their networks.

One of the main features of the CSACS1121K9 is its centralized user authentication capabilities. This device simplifies the process of validating user identities, allowing administrators to manage credentials for a variety of access methods, including web-based authentication, RADIUS, and TACACS+. This flexibility plays a significant role in diverse environments where different protocols may be required for various devices or applications.

The CSACS1121K9 is built on the robust Cisco Secure Access Control Server (ACS) platform. This platform supports a wide range of security policies, making it versatile enough for different organizational needs. With its capability to integrate seamlessly with other Cisco solutions and third-party platforms, the device enhances the overall security posture of an organization.

In terms of scalability, the CSACS1121K9 can support a substantial number of users and devices. This scalability ensures that as organizations grow, their access management system can scale proportionately without performance degradation. The ability to handle thousands of simultaneous authentication requests makes it suitable for both small companies and large enterprises.

Another significant characteristic of the CSACS1121K9 is its support for advanced visibility and reporting. Administrators can track authentication attempts, policy enforcement, and other critical events in real time. This level of monitoring is essential for compliance audits and helps organizations quickly react to potential security threats.

Moreover, the CSACS1121K9 includes capabilities for implementing role-based access control (RBAC). This feature allows organizations to define specific access rights based on user roles, which enhances security while facilitating efficient operations.

In conclusion, the Cisco Systems CSACS1121K9 is a powerful tool for organizations seeking to enhance their identity and access management frameworks. With its centralized user authentication, scalability, advanced reporting capabilities, and support for RBAC, it provides a robust solution that can adapt to the evolving security demands of modern networks. Whether deployed in a small business environment or within large enterprises, the CSACS1121K9 stands out for its comprehensive feature set and ability to integrate into existing security infrastructures.
Top Page Image Contents