Cisco Systems CSACS1121K9 manual Unpacking the Access Point, Basic Installation Guidelines

Page 29

Chapter 2 Installing the Access Point

Unpacking the Access Point

Unpacking the Access Point

Follow these steps to unpack the access point:

Step 1 Open the shipping container and carefully remove the contents.

Step 2 Return all packing materials to the shipping container and save it.

Step 3 Ensure that all items listed in the “Package Contents” section are included in the shipment. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative.

Package Contents

Each access point package contains the following items:

•Access point with power module

•Wall or ceiling mounting bracket

•Security hasp adapter

•Cubical partition mounting bracket assembly

•Horizontal surface mounting holster

•Mounting hardware kit

•Product quick start quide

•Product safety warnings document

•Cisco product registration and Cisco documentation feedback cards

Basic Installation Guidelines

Because the access point is a radio device, it is susceptible to interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:

•Ensure a site survey has been performed to determine the optimum placement of access points.

•For lightweight access points, check the latest release notes to ensure that your controller software version supports the access points to be installed. You can find the controller release notes by selecting your controller under Wireless LAN Controllers at this URL:

http://www.cisco.com/en/US/products/hw/wireless/tsd_products_support_category_home.html

•Ensure that access points are not mounted closer than 20 cm (7.9 in) from the body of all persons.

•Do not mount the access point within 3 feet of metal obstructions.

•Install the access point away from microwave ovens. Microwave ovens operate on the same frequency as the access point and can cause signal interference.

•Do not mount the access point outside of buildings.

•Do not mount the access points on building perimeter walls unless outside coverage is desired.

Cisco Aironet 1100 Series Access Point Hardware Installation Guide

 

OL-4309-07

2-3

 

 

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Corporate Headquarters Page N T E N T S Deploying the Access Points on the Wireless Network Finding the Software Version Chinese Translation B-7 Audience PrefacePurpose OrganizationViii ConventionsPreface Conventions Obtaining Documentation Related PublicationsCisco Product Security Overview Documentation FeedbackCisco.com Product Documentation DVD Ordering DocumentationProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsCisco Support Website Obtaining Technical AssistanceLocating the Product Serial Number Obtaining Additional Publications and Information Submitting a Service RequestDefinitions of Service Request Severity Xvi Lightweight Access Points Autonomous Access PointsOverview Product TerminologyOverview Ethernet Port Hardware FeaturesSingle Radio Operation LEDs Power SourcesUL 2043 Certification Network Examples with Autonomous Access PointsAnti-Theft Features Access point Root Unit on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeWorkgroup Bridge Configuration Central Unit in an All-Wireless NetworkTypical Layer 3 Network Configuration Example Network Example with Lightweight Access PointsOL-4309-07 Installing the Access Point General Safety Guidelines Safety InformationFCC Safety Compliance Statement Package Contents Unpacking the Access PointBasic Installation Guidelines 1shows the access point layout and connectors Access Point Layout and ConnectorsController Discovery Process for Lightweight Access Points Deploying the Access Points on the Wireless NetworkOL-4309-07 Access Point Power Options Connecting the Ethernet and Power CablesConnecting to an Ethernet Network with Local Power Powering Up the Access Point OL-4309-07 Mounting Instructions Mounting Method Materials Required Kit OverviewMounting Bracket Mounting on a Horizontal or Vertical SurfaceSuspended Ceiling Mounting Bracket Parts Mounting on a Suspended CeilingAccess Point Mounting Slots Remove a ceiling tile adjacent to the mounting location Mounting Above a Suspended CeilingSecurity Hasp Adapter Using the Security Hasp AdapterSecurity Hasp with Padlock Mounting on a Cubical Wall PartitionCubicle Wall Bracket Using the Desktop HolsterDesktop Holster Kensington Lock Using the Cable Lock FeatureOL-4309-07 GHz Radio Upgrade for Autonomous Access Points Unpacking the Radio Upgrade OverviewGo to the Removing a 2.4-GHz Radio section Removing the Back CoverRadio Card and Antenna Card Removing a 2.4-GHz RadioConnector pins Installing a 2.4-GHz RadioInserting Radio Card in Mini-PCI Connector Go to the Replacing the Back Cover section on Product compliance label Back cover Replacing the Back CoverFinding the Software Version OL-4309-07 Troubleshooting Autonomous Access Points Ethernet Status Radio Checking the Autonomous Access Point LEDsLED Default Ssid and Radio Behavior Checking Basic SettingsDefault IP Address Behavior WEP Keys Security SettingsEnabling the Radio Interfaces Running the Carrier Busy Test Running the Ping or Link Test Resetting to the Default ConfigurationUsing the Web Browser Interface Using the Mode ButtonReloading the Access Point Image Browser Http Interface Web Browser InterfaceObtaining the Tftp Server Software Obtaining the Access Point Image FileOL-4309-07 Troubleshooting Lightweight Access Points Using Dhcp Option Guidelines for Using 1100 Series Lightweight Access PointsAccess Points LEDs Checking the Lightweight Access Point LEDsMessage Ethernet Status Radio Type Enabled see the Mode Button Setting section on Returning the Access Point to Autonomous ModeMode Button Setting Obtaining the Autonomous Access Point Image FileObtaining the Tftp Server Software OL-4309-07 Translated Safety Warnings OL-4309-07 Declarations of Conformity and Regulatory Information For Home or Office USE Canadian Compliance Statement Vcci Statement for Japan Industry-CanadaOL-4309-07 EMC Japanese Translation Declaration of Conformity for RF ExposureEnglish Translation All Access PointsAccess Point Models Operation of Cisco Aironet Access Points in BrazilPortuguese Translation Declaration of Conformity StatementsOL-4309-07 Page OL-4309-07 Page OL-4309-07 Category Specifications Access Point SpecificationsRadio GHz Radio To UL 2043 and they should not be placed in a building’s Category Specifications Channels and Maximum Power Levels OL-4309-07 Priming Lightweight Access Points Prior to Deployment OL-4309-07 Page Access Points Lightweight Access Point Vendor Class Identifier VCI Quotation marks must be included Configuring Option 43 for 1000 Series Access PointsType + Length + Value OL-4309-07 O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2

CSACS1121K9 specifications

Cisco Systems CSACS1121K9 is a part of Cisco's comprehensive suite of security solutions tailored for identity and access management. This device, recognized for its reliability and functionality, plays a crucial role in ensuring that organizations can efficiently manage user access across their networks.

One of the main features of the CSACS1121K9 is its centralized user authentication capabilities. This device simplifies the process of validating user identities, allowing administrators to manage credentials for a variety of access methods, including web-based authentication, RADIUS, and TACACS+. This flexibility plays a significant role in diverse environments where different protocols may be required for various devices or applications.

The CSACS1121K9 is built on the robust Cisco Secure Access Control Server (ACS) platform. This platform supports a wide range of security policies, making it versatile enough for different organizational needs. With its capability to integrate seamlessly with other Cisco solutions and third-party platforms, the device enhances the overall security posture of an organization.

In terms of scalability, the CSACS1121K9 can support a substantial number of users and devices. This scalability ensures that as organizations grow, their access management system can scale proportionately without performance degradation. The ability to handle thousands of simultaneous authentication requests makes it suitable for both small companies and large enterprises.

Another significant characteristic of the CSACS1121K9 is its support for advanced visibility and reporting. Administrators can track authentication attempts, policy enforcement, and other critical events in real time. This level of monitoring is essential for compliance audits and helps organizations quickly react to potential security threats.

Moreover, the CSACS1121K9 includes capabilities for implementing role-based access control (RBAC). This feature allows organizations to define specific access rights based on user roles, which enhances security while facilitating efficient operations.

In conclusion, the Cisco Systems CSACS1121K9 is a powerful tool for organizations seeking to enhance their identity and access management frameworks. With its centralized user authentication, scalability, advanced reporting capabilities, and support for RBAC, it provides a robust solution that can adapt to the evolving security demands of modern networks. Whether deployed in a small business environment or within large enterprises, the CSACS1121K9 stands out for its comprehensive feature set and ability to integrate into existing security infrastructures.
Top Page Image Contents