Cisco Systems ASA5515K9, kygjygcjgf, ASA5525IPSK9 manual Index finger placement Thumb placement

Page 60

Chapter 4 Maintenance and Upgrade Procedures for the ASA 5500-X

Installing an I/O Card

Figure 4-6 Lift the I/O Card Upward to Release it

1

1

1Index finger placement

2Thumb placement

2

2

331354

Step 9 Insert the new I/O card into the chassis. (See Figure 4-7.) The I/O card fits properly if the following criteria are met:

a.The PCIe bus is properly inserted on the motherboard

b.The small black plastic guide slides all the way into the chassis

c.The two hooks on the assembly plug into the two slots on the edge of the chassis

Figure 4-7 Installing the I/O Card

331399

Cisco ASA 5500-X Series Hardware Installation Guide

4-6

Image 60
Contents Cisco ASA 5500-X Series Hardware Installation Guide Page N T E N T S System Installing and Removing SSDs Contents Cisco ASA 5500-X Series Hardware Installation Guide Contents Document ObjectivesDocument Conventions Installation Warnings ViiiCisco ASA 5500-X Series Hardware Installation Guide Cisco ASA 5500-X Series Hardware Installation Guide Circuit Breaker 15A Warning Where to Find Safety and Warning Information Related DocumentationXiii Xiv Information about the ASA Cisco ASA 5500-X Series Chassis Overview Internal and External USB Flash DrivesInternal USB Drive Optional External USB DrivesSolid State Drives Online Insertion and Removal SupportFAT 32 File System Viewing Flash MemoryAlarm LED Management 0/0 InterfaceASA 5500-X I/O Cards SFP ModulesASA Chassis Panels Front Panel LEDsDescription VPN 13 12 Rear Panel LEDs HD1LED Rear Panel Ports See the Management 0/0 Interface section on7shows the rear panel ports for the ASA 5545-X and ASA Power Supply AC Power Supply and DC Power Supply Hardware Specifications Console Cable Pinouts RJ-45 Console CableASA Non-Operating ConditionsSignal Pin 9shows the RJ 45 cableSignal RJ-45 Pin DB-9 Pin RJ-45 to DB-9 Console AdapterInstallation Overview Safety RecommendationsMaintaining Safety with Electricity General Site Requirements Preventing Electrostatic Discharge DamageWorking in an ESD Environment Preventive Site Configuration Power Supply ConsiderationsSite Environment Appliance Coupler AC Power Supply Locale Part Number Length Plug RatingConfiguring Equipment Racks CAB-IND-10ARack Mounting the Chassis Rack Mounting GuidelinesDetailed Steps Airflow Direction Detailed Steps See Figure Verify the Box Contents Verify the Rack TypeTools Required Front 330905 No additional hardware is necessary for the rear adapter Round and Square Hole Racks Secure the other outer slide rail to the rackThreaded Hole Racks Secure the chassis to the rack with the front captive screws Guidelines Network Management PC Unsecured Secured Installing and Connecting the ASA Page Removing and Replacing the Chassis Cover Removing the Chassis CoverReplacing the Chassis Cover Removing the Chassis CoverInstalling an I/O Card Replacing the Chassis CoverI/O Card Location Removing the Regex Cable Connector Index finger placement Thumb placement Pushing the cover toward the rear of the chassis 10 Removing the Regex Cable Connector 11 Lift the I/O Card Upward to Release it Close the green connector clamp Installing and Removing the SFP Modules Installing the SFP ModuleRemoving the SFP Module Mylar tab Actuator/Button Bale-clasp Plastic collarRemoving and Installing the Power Supply Removing and Installing the AC Power Supply16 Removing the Slot Cover Installing the DC Input Power 19 Back Power Supply IndicatorsFixed fan Fixed DC power supply 22 Stripping the DC Input Power Source Wire 24shows the DC power supply with lead wires Removing and Installing the DC Power Supply 25 Complete DC Secure Tie Wrap26 Removing the Slot Cover Installing and Removing the Solid State Drive for Installation ScenariosInstalling and Removing SSDs 30 Removing the SSD from the ASA 5512/5515/5525-X32 Installing the SSD in the ASA 5512/5515/5525-X Page Numerics IN-2