Cisco Systems ASA5515K9 manual Installing and Removing the SFP Modules, Installing the SFP Module

Page 65

Chapter 4 Maintenance and Upgrade Procedures for the ASA 5500-X

Installing and Removing the SFP Modules

Installing and Removing the SFP Modules

The SFP module is a hot-swappable input/output device that plugs into the SFP ports. This section describes how to install and remove the SFP modules in the ASA to provide optical Gigabit Ethernet connectivity, and it includes the following topics:

Installing the SFP Module, page 4-11

Removing the SFP Module, page 4-12

Caution Protect your SFP modules by inserting clean dust plugs into the SFPs after the cables are extracted from them. Be sure to clean the optic surfaces of the fiber cables before you plug them back into the optical bores of another SFP module. Avoid getting dust and other contaminants into the optical bores of your SFP modules. The optics do not operate correctly when obstructed with dust.

Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 70

Installing the SFP Module

To install the SFP module, perform the following steps.

Detailed Steps

Step 1 Align the SFP module with the port, and slide the SFP module into the port slot until it locks into position, as shown in Figure 4-14.

Figure 4-14 Installing an SFP Module

3

2

132985

1

1

3

Optical port plug

2

SFP port slot

 

 

 

SFP module

Caution Do not remove the optical port plugs from the SFP until you are ready to connect the cabling.

Cisco ASA 5500-X Series Hardware Installation Guide

4-11

Image 65
Contents Cisco ASA 5500-X Series Hardware Installation Guide Page N T E N T S System Installing and Removing SSDs Contents Cisco ASA 5500-X Series Hardware Installation Guide Document Conventions ContentsDocument Objectives Viii Installation WarningsCisco ASA 5500-X Series Hardware Installation Guide Cisco ASA 5500-X Series Hardware Installation Guide Circuit Breaker 15A Warning Related Documentation Where to Find Safety and Warning InformationXiii Xiv Information about the ASA Internal and External USB Flash Drives Cisco ASA 5500-X Series Chassis OverviewInternal USB Drive Optional External USB DrivesOnline Insertion and Removal Support Solid State DrivesFAT 32 File System Viewing Flash MemoryManagement 0/0 Interface Alarm LEDSFP Modules ASA 5500-X I/O CardsDescription ASA Chassis PanelsFront Panel LEDs VPN 13 12 HD1 Rear Panel LEDsLED See the Management 0/0 Interface section on Rear Panel Ports7shows the rear panel ports for the ASA 5545-X and ASA Power Supply AC Power Supply and DC Power Supply Hardware Specifications RJ-45 Console Cable Console Cable PinoutsASA Non-Operating Conditions9shows the RJ 45 cable Signal PinRJ-45 to DB-9 Console Adapter Signal RJ-45 Pin DB-9 PinSafety Recommendations Installation OverviewMaintaining Safety with Electricity Working in an ESD Environment General Site RequirementsPreventing Electrostatic Discharge Damage Site Environment Preventive Site ConfigurationPower Supply Considerations Locale Part Number Length Plug Rating Appliance Coupler AC Power SupplyCAB-IND-10A Configuring Equipment RacksRack Mounting Guidelines Rack Mounting the ChassisDetailed Steps Airflow Direction Detailed Steps See Figure Tools Required Verify the Box ContentsVerify the Rack Type Front 330905 No additional hardware is necessary for the rear adapter Secure the other outer slide rail to the rack Round and Square Hole RacksThreaded Hole Racks Secure the chassis to the rack with the front captive screws Guidelines Network Management PC Unsecured Secured Installing and Connecting the ASA Page Removing the Chassis Cover Removing and Replacing the Chassis CoverRemoving the Chassis Cover Replacing the Chassis CoverReplacing the Chassis Cover Installing an I/O CardI/O Card Location Removing the Regex Cable Connector Index finger placement Thumb placement Pushing the cover toward the rear of the chassis 10 Removing the Regex Cable Connector 11 Lift the I/O Card Upward to Release it Close the green connector clamp Installing the SFP Module Installing and Removing the SFP ModulesMylar tab Actuator/Button Bale-clasp Plastic collar Removing the SFP ModuleRemoving and Installing the AC Power Supply Removing and Installing the Power Supply16 Removing the Slot Cover 19 Back Power Supply Indicators Installing the DC Input PowerFixed fan Fixed DC power supply 22 Stripping the DC Input Power Source Wire 24shows the DC power supply with lead wires 25 Complete DC Secure Tie Wrap Removing and Installing the DC Power Supply26 Removing the Slot Cover Installation Scenarios Installing and Removing the Solid State Drive for30 Removing the SSD from the ASA 5512/5515/5525-X Installing and Removing SSDs32 Installing the SSD in the ASA 5512/5515/5525-X Page Numerics IN-2