Cisco Systems ASA5525IPSK9, ASA5515K9, kygjygcjgf, ASA5512AW1YPR Removing the Regex Cable Connector

Page 62

Chapter 4 Maintenance and Upgrade Procedures for the ASA 5500-X

Installing an I/O Card

Step 6 To expose the blue connector on the end of the Regex flexible circuit, push down on the center of the green connector clamp, and lift the end of the clamp to release the lock. (See Figure 4-9.)

Figure 4-9 Removing the Connector Clamp

 

PUSH AND LIFT TAB

 

 

-C-

-A-

 

-B-

 

-B-

 

 

 

 

-A-

-B-

 

-B-

331353

Step 7 Disconnect the blue connector from the board by lifting carefully but firmly. (See Figure 4-10.)

Figure 4-10 Removing the Regex Cable Connector

 

 

-C-

-A-

 

-B-

 

 

 

-B-

 

 

 

 

 

 

-A-

-B-

 

 

-B-

331350

Cisco ASA 5500-X Series Hardware Installation Guide

4-8

Image 62
Contents Cisco ASA 5500-X Series Hardware Installation Guide Page N T E N T S System Installing and Removing SSDs Contents Cisco ASA 5500-X Series Hardware Installation Guide Document Conventions ContentsDocument Objectives Installation Warnings ViiiCisco ASA 5500-X Series Hardware Installation Guide Cisco ASA 5500-X Series Hardware Installation Guide Circuit Breaker 15A Warning Where to Find Safety and Warning Information Related DocumentationXiii Xiv Information about the ASA Internal USB Drive Cisco ASA 5500-X Series Chassis OverviewInternal and External USB Flash Drives Optional External USB DrivesFAT 32 File System Solid State DrivesOnline Insertion and Removal Support Viewing Flash MemoryAlarm LED Management 0/0 InterfaceASA 5500-X I/O Cards SFP ModulesDescription ASA Chassis PanelsFront Panel LEDs VPN 13 12 Rear Panel LEDs HD1LED Rear Panel Ports See the Management 0/0 Interface section on7shows the rear panel ports for the ASA 5545-X and ASA Power Supply AC Power Supply and DC Power Supply Hardware Specifications ASA Console Cable PinoutsRJ-45 Console Cable Non-Operating ConditionsSignal Pin 9shows the RJ 45 cableSignal RJ-45 Pin DB-9 Pin RJ-45 to DB-9 Console AdapterInstallation Overview Safety RecommendationsMaintaining Safety with Electricity Working in an ESD Environment General Site RequirementsPreventing Electrostatic Discharge Damage Site Environment Preventive Site ConfigurationPower Supply Considerations Appliance Coupler AC Power Supply Locale Part Number Length Plug RatingConfiguring Equipment Racks CAB-IND-10ARack Mounting the Chassis Rack Mounting GuidelinesDetailed Steps Airflow Direction Detailed Steps See Figure Tools Required Verify the Box ContentsVerify the Rack Type Front 330905 No additional hardware is necessary for the rear adapter Round and Square Hole Racks Secure the other outer slide rail to the rackThreaded Hole Racks Secure the chassis to the rack with the front captive screws Guidelines Network Management PC Unsecured Secured Installing and Connecting the ASA Page Removing and Replacing the Chassis Cover Removing the Chassis CoverReplacing the Chassis Cover Removing the Chassis CoverInstalling an I/O Card Replacing the Chassis CoverI/O Card Location Removing the Regex Cable Connector Index finger placement Thumb placement Pushing the cover toward the rear of the chassis 10 Removing the Regex Cable Connector 11 Lift the I/O Card Upward to Release it Close the green connector clamp Installing and Removing the SFP Modules Installing the SFP ModuleRemoving the SFP Module Mylar tab Actuator/Button Bale-clasp Plastic collarRemoving and Installing the Power Supply Removing and Installing the AC Power Supply16 Removing the Slot Cover Installing the DC Input Power 19 Back Power Supply IndicatorsFixed fan Fixed DC power supply 22 Stripping the DC Input Power Source Wire 24shows the DC power supply with lead wires Removing and Installing the DC Power Supply 25 Complete DC Secure Tie Wrap26 Removing the Slot Cover Installing and Removing the Solid State Drive for Installation ScenariosInstalling and Removing SSDs 30 Removing the SSD from the ASA 5512/5515/5525-X32 Installing the SSD in the ASA 5512/5515/5525-X Page Numerics IN-2