Cisco Systems ASA5525IPSK9, ASA5515K9, kygjygcjgf, ASA5512AW1YPR, ASA5555IPSK9 manual

Page 2

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco ASA 5500-X Series Hardware Installation Guide © 2012-2013 Cisco Systems, Inc. All rights reserved.

Image 2 Cisco Systems ASA5525IPSK9, ASA5515K9, kygjygcjgf, ASA5512AW1YPR, ASA5555IPSK9 manual
Contents Cisco ASA 5500-X Series Hardware Installation Guide Page N T E N T S System Installing and Removing SSDs Contents Cisco ASA 5500-X Series Hardware Installation Guide Document Conventions ContentsDocument Objectives Installation Warnings ViiiCisco ASA 5500-X Series Hardware Installation Guide Cisco ASA 5500-X Series Hardware Installation Guide Circuit Breaker 15A Warning Where to Find Safety and Warning Information Related DocumentationXiii Xiv Information about the ASA Internal USB Drive Cisco ASA 5500-X Series Chassis OverviewInternal and External USB Flash Drives Optional External USB DrivesFAT 32 File System Solid State DrivesOnline Insertion and Removal Support Viewing Flash MemoryAlarm LED Management 0/0 InterfaceASA 5500-X I/O Cards SFP ModulesDescription ASA Chassis PanelsFront Panel LEDs VPN 13 12 Rear Panel LEDs HD1LED Rear Panel Ports See the Management 0/0 Interface section on7shows the rear panel ports for the ASA 5545-X and ASA Power Supply AC Power Supply and DC Power Supply Hardware Specifications ASA Console Cable PinoutsRJ-45 Console Cable Non-Operating ConditionsSignal Pin 9shows the RJ 45 cableSignal RJ-45 Pin DB-9 Pin RJ-45 to DB-9 Console AdapterInstallation Overview Safety RecommendationsMaintaining Safety with Electricity Working in an ESD Environment General Site RequirementsPreventing Electrostatic Discharge Damage Site Environment Preventive Site ConfigurationPower Supply Considerations Appliance Coupler AC Power Supply Locale Part Number Length Plug RatingConfiguring Equipment Racks CAB-IND-10ARack Mounting the Chassis Rack Mounting GuidelinesDetailed Steps Airflow Direction Detailed Steps See Figure Tools Required Verify the Box ContentsVerify the Rack Type Front 330905 No additional hardware is necessary for the rear adapter Round and Square Hole Racks Secure the other outer slide rail to the rackThreaded Hole Racks Secure the chassis to the rack with the front captive screws Guidelines Network Management PC Unsecured Secured Installing and Connecting the ASA Page Removing and Replacing the Chassis Cover Removing the Chassis CoverReplacing the Chassis Cover Removing the Chassis CoverInstalling an I/O Card Replacing the Chassis CoverI/O Card Location Removing the Regex Cable Connector Index finger placement Thumb placement Pushing the cover toward the rear of the chassis 10 Removing the Regex Cable Connector 11 Lift the I/O Card Upward to Release it Close the green connector clamp Installing and Removing the SFP Modules Installing the SFP ModuleRemoving the SFP Module Mylar tab Actuator/Button Bale-clasp Plastic collarRemoving and Installing the Power Supply Removing and Installing the AC Power Supply16 Removing the Slot Cover Installing the DC Input Power 19 Back Power Supply IndicatorsFixed fan Fixed DC power supply 22 Stripping the DC Input Power Source Wire 24shows the DC power supply with lead wires Removing and Installing the DC Power Supply 25 Complete DC Secure Tie Wrap26 Removing the Slot Cover Installing and Removing the Solid State Drive for Installation ScenariosInstalling and Removing SSDs 30 Removing the SSD from the ASA 5512/5515/5525-X32 Installing the SSD in the ASA 5512/5515/5525-X Page Numerics IN-2