Cisco Systems ASA5512AW1YPR, ASA5515K9, kygjygcjgf Removing and Installing the DC Power Supply

Page 73

Chapter 4 Maintenance and Upgrade Procedures for the ASA 5500-X

Removing and Installing the Power Supply

Step 9 Use a tie wrap to secure the wires coming from the power supply to the rack so that the wires cannot be pulled from the power supply by casual contact. Make sure the tie wrap allows for some slack in the ground wire. Figure 4-25shows the DC power supply with the wires inserted and the tie wrap secured.

Figure 4-25 Complete DC Secure Tie Wrap

333061

1

1

Lead wires secured with a tie wrap

Step 10 Remove the tape (if any) from the circuit breaker switch handle, and move the circuit breaker switch handle to the On position. The power supply indicators light up when power is supplied to the appliance.

Removing and Installing the DC Power Supply

Note This procedure applies only to the appliances with a removable DC power supply (ASA 5545-X and ASA 5555-X).

To remove and install a DC power supply, perform the following steps:

Step 1 Make sure that the chassis ground is connected on the chassis before you begin installing the DC power supply, as described in “Working in an ESD Environment” section on page 2-3.

Step 2 Turn off the circuit breaker to the power supply.

Step 3 At the back of the appliance, place the Standby switch into the Standby position.

Step 4 Move the circuit-breaker switch handle to the Off position, and apply tape to hold it in the Off position.

Step 5 If you are adding an additional power supply, from the back of the appliance, push the lever on the slot cover to the left to release it, grasp the handle of the slot cover, and pull it away from the chassis. (See Figure 4-26.) Save the slot cover for future use. Continue with Step 7.

Cisco ASA 5500-X Series Hardware Installation Guide

4-19

Image 73
Contents Cisco ASA 5500-X Series Hardware Installation Guide Page N T E N T S System Installing and Removing SSDs Contents Cisco ASA 5500-X Series Hardware Installation Guide Document Objectives ContentsDocument Conventions Viii Installation WarningsCisco ASA 5500-X Series Hardware Installation Guide Cisco ASA 5500-X Series Hardware Installation Guide Circuit Breaker 15A Warning Related Documentation Where to Find Safety and Warning InformationXiii Xiv Information about the ASA Internal and External USB Flash Drives Cisco ASA 5500-X Series Chassis OverviewInternal USB Drive Optional External USB DrivesOnline Insertion and Removal Support Solid State DrivesFAT 32 File System Viewing Flash MemoryManagement 0/0 Interface Alarm LEDSFP Modules ASA 5500-X I/O CardsFront Panel LEDs ASA Chassis PanelsDescription VPN 13 12 HD1 Rear Panel LEDsLED See the Management 0/0 Interface section on Rear Panel Ports7shows the rear panel ports for the ASA 5545-X and ASA Power Supply AC Power Supply and DC Power Supply Hardware Specifications RJ-45 Console Cable Console Cable PinoutsASA Non-Operating Conditions9shows the RJ 45 cable Signal PinRJ-45 to DB-9 Console Adapter Signal RJ-45 Pin DB-9 PinSafety Recommendations Installation OverviewMaintaining Safety with Electricity Preventing Electrostatic Discharge Damage General Site RequirementsWorking in an ESD Environment Power Supply Considerations Preventive Site ConfigurationSite Environment Locale Part Number Length Plug Rating Appliance Coupler AC Power SupplyCAB-IND-10A Configuring Equipment RacksRack Mounting Guidelines Rack Mounting the ChassisDetailed Steps Airflow Direction Detailed Steps See Figure Verify the Rack Type Verify the Box ContentsTools Required Front 330905 No additional hardware is necessary for the rear adapter Secure the other outer slide rail to the rack Round and Square Hole RacksThreaded Hole Racks Secure the chassis to the rack with the front captive screws Guidelines Network Management PC Unsecured Secured Installing and Connecting the ASA Page Removing the Chassis Cover Removing and Replacing the Chassis CoverRemoving the Chassis Cover Replacing the Chassis CoverReplacing the Chassis Cover Installing an I/O CardI/O Card Location Removing the Regex Cable Connector Index finger placement Thumb placement Pushing the cover toward the rear of the chassis 10 Removing the Regex Cable Connector 11 Lift the I/O Card Upward to Release it Close the green connector clamp Installing the SFP Module Installing and Removing the SFP ModulesMylar tab Actuator/Button Bale-clasp Plastic collar Removing the SFP ModuleRemoving and Installing the AC Power Supply Removing and Installing the Power Supply16 Removing the Slot Cover 19 Back Power Supply Indicators Installing the DC Input PowerFixed fan Fixed DC power supply 22 Stripping the DC Input Power Source Wire 24shows the DC power supply with lead wires 25 Complete DC Secure Tie Wrap Removing and Installing the DC Power Supply26 Removing the Slot Cover Installation Scenarios Installing and Removing the Solid State Drive for30 Removing the SSD from the ASA 5512/5515/5525-X Installing and Removing SSDs32 Installing the SSD in the ASA 5512/5515/5525-X Page Numerics IN-2