Cisco Systems quick start After Installation, Power Off the Cisco ASR 1004 Router

Page 30

7After Installation

Follow the instructions in this section to replace components after installation. The following topics are covered in this section:

Power Off the Cisco ASR 1004 Router, page 30

Remove and Replace a Power Supply, page 30

Remove the Shared Port Adapter, page 35

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

 

Statement 1030

 

 

Power Off the Cisco ASR 1004 Router

This section explains how to shut down the Cisco ASR 1000 Series router. It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reload operation is complete, then the Cisco ASR 1004 Router can be powered off safely.

To remove power from the Cisco ASR 1000 Series Router, follow this procedure:

Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.

Step 2 Before you shutdown power to the router, issue the IOS reload command to halt the system and then wait for ROM Monitor to execute before proceeding to the next step. The following screen shot shows an example of the reload command:

Router#reload

Proceed with reload? [confirm]

*Jun 18 19:38:21.870: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command.

Step 3 Remove any power cables from the Cisco ASR 1004 Router.

Note After powering off the router, wait a minimum of 30 seconds before powering it on again.

Remove and Replace a Power Supply

This section provides instructions for removing and replacing the AC power supply and the DC power supply in a Cisco ASR 1004 Router. Before you begin, make certain the chassis is grounded.

Remove and Then Replace an AC Power Supply

To remove a live Cisco ASR 1004 Router AC power supply that is not operating normally (and then replace the AC power supply within five minutes), follow this procedure:

Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.

Step 2 Before you turn off a power supply, make certain the chassis is grounded.

Step 3 Turn the power supply Standby switch to the Standby position.of the power supply.

Step 4 Unplug the power cable from the AC inlet on the back of the power supply and the power source.

Step 5 Unscrew the power supply captive screws.

30

Image 30
Contents Cisco ASR 1004 Router Documentation and Resources Document Revision HistorySite Preparation and Unpacking Prepare for InstallationPrepare for Equipment Shelf or Tabletop Installation Tools and PartsPrepare for Rack-Mount Installation Rack-Mount the RouterAttach the Rack-Mount Brackets-Chassis Front-Mounted Attach the Rack-Mount Brackets-Chassis Rear-Mounted Four-Post Rack Installation Installing the Cisco ASR 1004 Router in a Four-Post RackPage Two-Post Rack Installation Installing a Cisco ASR 1004 Router in a Two-Post RackAttach the Cable-Management Bracket Chassis Ground Connection Installation Chassis ground connector on the Cisco ASR 1004 Router Connect the Router to the Network Console and Auxiliary Port Cable ConnectionsCisco ASR1000-RP1 Enet Management Port Connector Management Ethernet Port Cable ConnectionStart the System Install Cables in the Cable-Management BracketConnect AC Power to the Router Connect the Shared Port Adapter CablesConnect DC Power to the Router Cisco ASR 1004 Router AC Power SupplyUnit. Statement Installing the DC Ground Lugs Wiring the DC-Input Power Source Cisco ASR 1004 Router DC Power Supply Terminal Block Verifying Power Supply Operation Start the Cisco ASR 1004 RouterLED Page Page Configure the Router Using the Console InterfaceConfigure Global Parameters Using the Setup Facility OK? No clns routing Tftptimeout Page Check the Running Configuration Settings Save the Running Configuration to NvramPerform Other Configuration Tasks After Installation Power Off the Cisco ASR 1004 RouterRemove and Replace a Power Supply Remove and Then Replace a DC Power Supply Page End View All measurements in inches 267 Holes Install and Remove the SPA Interface Processor SIP Remove the Shared Port Adapter ASR1000-SIP10Page USA