Cisco Systems ASR 1004 quick start Tftptimeout

Page 27

shutdown

no ip address

dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit

!

end

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

Enter your selection [2]:

Router#reload

Proceed with reload? [confirm]

*Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command.

System Bootstrap, Version 12.2(20071105:235056) [gschnorr-mcp_rommon_rel_1_25 101], DEVELOPMENT SOFTWARE Copyright (c) 1994-2007 by cisco Systems, Inc.

Compiled Mon 05-Nov-07 16:50 by gschnorr-mcp_rommon_rel_1_25

Current image running: Boot ROM1

Last reset cause: LocalSoft

SATA drive PCI config error

ASR1004-RP1 platform with 2097152 Kbytes of main memory

rommon 1 > b tftp:images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin

IP_ADDRESS: 2.1.6.5

IP_SUBNET_MASK: 255.255.0.0 DEFAULT_GATEWAY: 2.1.0.1

TFTP_SERVER: 2.0.0.2

TFTP_FILE: images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin Using midplane macaddr

TFTP_MACADDR: 00:14:a8:ff:42:ff

TFTP_VERBOSE: Progress TFTP_RETRY_COUNT: 18

TFTP_TIMEOUT: 7200

TFTP_CHECKSUM: Yes

ETHER_PORT: 3 ETHER_SPEED_MODE: Auto Detect

link up 1000Mbps/FD.......

Receiving images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin from 2.0.0.2

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!

File reception completed.

Boot image size = 206741708 (0xc52a0cc) bytes

Using midplane macaddr

Package header rev 0 structure detected Calculating SHA-1 hash...done validate_package: SHA-1 hash:

calculated a8301e1e:17821e94:07654c49:4ca6fe49:518af2c2 expected a8301e1e:17821e94:07654c49:4ca6fe49:518af2c2

Image validated

PPC/IOS XE loader version: 0.0.3

loaded at: 00800000 0CD2C004

27

Image 27

Contents Cisco ASR 1004 Router Document Revision History Documentation and ResourcesTools and Parts Prepare for InstallationPrepare for Equipment Shelf or Tabletop Installation Site Preparation and UnpackingPrepare for Rack-Mount Installation Rack-Mount the RouterAttach the Rack-Mount Brackets-Chassis Front-Mounted Attach the Rack-Mount Brackets-Chassis Rear-Mounted Installing the Cisco ASR 1004 Router in a Four-Post Rack Four-Post Rack InstallationPage Installing a Cisco ASR 1004 Router in a Two-Post Rack Two-Post Rack InstallationAttach the Cable-Management Bracket Chassis Ground Connection Installation Chassis ground connector on the Cisco ASR 1004 Router Console and Auxiliary Port Cable Connections Connect the Router to the NetworkManagement Ethernet Port Cable Connection Cisco ASR1000-RP1 Enet Management Port ConnectorConnect the Shared Port Adapter Cables Install Cables in the Cable-Management BracketConnect AC Power to the Router Start the SystemCisco ASR 1004 Router AC Power Supply Connect DC Power to the RouterUnit. Statement Installing the DC Ground Lugs Wiring the DC-Input Power Source Cisco ASR 1004 Router DC Power Supply Terminal Block Start the Cisco ASR 1004 Router Verifying Power Supply OperationLED Page Page Configure the Router Using the Console InterfaceConfigure Global Parameters Using the Setup Facility OK? No clns routing Tftptimeout Page Check the Running Configuration Settings Save the Running Configuration to NvramPerform Other Configuration Tasks After Installation Power Off the Cisco ASR 1004 RouterRemove and Replace a Power Supply Remove and Then Replace a DC Power Supply Page End View All measurements in inches 267 Holes Install and Remove the SPA Interface Processor SIP ASR1000-SIP10 Remove the Shared Port AdapterPage USA