Cisco Systems 12010, 12810, 12410 manual OL-11496-01

Page 45

Chapter 4 System Startup and Basic System Configuration

Using RP Flash Memory Cards

Step 3 Insert the card into the appropriate slot until the card completely seats in the connector and the ejector button pops out (see Figure 4-5b).

Caution The flash memory card is keyed for proper insertion. The ejector button does not pop out unless the card is inserted correctly. Part of the card remains outside of the slot even when the card is properly seated. Do not attempt to force the card deeper into the slot after the ejector button pops out.

Step 4 Replace the flash memory card slot cover.

Use the following procedure to remove a flash memory card.

Step 1 Remove the flash memory slot cover by loosening its captive screw (illustration is shown without the cover for clarity).

Step 2 Press the appropriate ejector button to eject the card from the connector at the back of the slot (see Figure 4-5c).

Step 3 Pull the card from the slot and place it in an antistatic bag to protect it from ESD damage.

Step 4 Replace the flash memory card slot cover.

 

 

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

 

 

 

 

 

 

OL-11496-01

 

 

4-45

 

 

 

Image 45
Contents System Startup and Basic System Configuration Sources of Cisco IOS Software Preconfiguration RequirementsBoot Process Overview Powering On the Router and Observing the Boot Process LED Display1 Meaning Source ProcessorPRI LED Display Meaning SourceMII Line Card Alphanumeric LED Displays-Partial View Shown Meaning SourceRomi OL-11496-01 Manually Booting the System Dir bootflash Booting from the Cisco IOS Software ImageLocating a Valid Cisco IOS Software Image Dir slot0Boot flash Command PurposeConfiguring the Router Cisco IOS User Interface Cisco IOS User Interface Command ModesPrivileged Exec Mode User Exec ModeInterface Configuration Mode Global Configuration ModeSubinterface Configuration Mode Using Setup for Configuration ChangesMay enter a question mark ? for help SDCC1/0 No ip routing Configuring Global Parameters Using the Setup Facility Configuring Host Name Configuring Protocols Configuring Network InterfacesConfiguring Line Card Interfaces Milo# show version Enter the enable command and password if prompted Using Global Configuration ModeMilo# configure terminal Verifying Running Configuration File SettingsMilo# copy running-config startup-config Router# show running-configSaving the Running Configuration Settings to Nvram Viewing the Running Configuration Settings Configuring the Software Configuration Register Bit Number Hexadecimal Value Meaning/Function Boot Field Setting Software Configuration SettingsCiscobootfieldvalue-processorname Changing Software Configuration Register Settings Miloconfig# config-register 0xvalue Reboot the systemLow-Order Bits in the Software Configuration Register Action/Filename Bit Bit Address net host High-Order Bits in the Software Configuration Register9600 Rommon 1 config-register Recovering a Lost PasswordEnter the initialize command to initialize the router Milo# show startup-config Installing and Removing a Flash Memory Card Using RP Flash Memory CardsOL-11496-01 Installing and Removing a Flash Memory Card Milo# format slot0 Formatting a New Flash Memory CardSpecifying a Cisco IOS Software Image to Boot the System Flash Memory Commands Pwd CommandCd Command Dir Command Delete CommandMilo# dir slot0 Milo# squeeze slot0 Squeeze CommandBooting from Flash Memory Miloconfig# boot system flash slot0myfile1Copying Image Files to or From Flash Memory Milo# copy tftpmyfile1 slot0myfile1 Milo# copy tftpfilename bootflashslot0slot1 filenameCopying a Cisco IOS Software Image into a Flash Memory Card Milo# copy tftpnew.image slot0new.image Milo# copy slot1image.new slot0image.new Copying Cisco IOS Software Images Between Flash Memory CardsMilo# configure terminal Copy startup-config slot0 slot1 filename Milo# show bootvarMilo# copy startup-config slot0myfile2 Milo# copy running-config slot0myfile2 Copy running-config slot0slot1filenameCopy slot0slot1filename startup-config Milo# copy slot0myfile startup-configMilo# copy startup-config running-config Recovering from Locked Blocks in Flash Memory Cards Post-Installation Procedures OL-11496-01