Cisco Systems 12410, 12010, 12810 manual Milo# copy tftpfilename bootflashslot0slot1 filename

Page 53

Chapter 4 System Startup and Basic System Configuration

Using RP Flash Memory Cards

Use the following command to copy a file to flash memory.

Milo# copy tftp:filename [bootflash:slot0:slot1:] filename

Where:

•tftp:filename specifies the source and name of the file to be copied.

•[bootflash: slot0: slot1:] filename specifies the destination flash device and name of the file.

The destination flash device can be one of the following:

–bootflash:—Specifies that the file is to be copied to the flash memory SIMM on the RP.

–slot0:—Specifies that the file is to be copied to the flash memory card in slot 0.

–slot 1:—Specifies that the file is to be copied to the flash memory card in slot 1.

		The following is typical output generated using the copy tftp:filename command.
		Milo# copy tftp:myfile1 slot0:myfile1
		20575008 bytes available on device slot0, proceed? [confirm]
		Address or name of remote host [1.1.1.1]?
		Loading new.image from 1.1.1.1 (via Ethernet0):
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
		!!!!!![OK - 7799951/15599616 bytes]
		CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
		CC
		CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
		C
		CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
		CC
		Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

	OL-11496-01			4-53
	OL-11496-01			4-53

Image 53

Contents System Startup and Basic System Configuration Sources of Cisco IOS Software Preconfiguration RequirementsBoot Process Overview Powering On the Router and Observing the Boot Process LED Display1 Meaning Source ProcessorPRI LED Display Meaning SourceMII Line Card Alphanumeric LED Displays-Partial View Shown Meaning SourceRomi OL-11496-01 Manually Booting the System Dir bootflash Booting from the Cisco IOS Software ImageLocating a Valid Cisco IOS Software Image Dir slot0Boot flash Command PurposeConfiguring the Router Cisco IOS User Interface Cisco IOS User Interface Command ModesPrivileged Exec Mode User Exec ModeInterface Configuration Mode Global Configuration ModeSubinterface Configuration Mode Using Setup for Configuration ChangesMay enter a question mark ? for help SDCC1/0 No ip routing Configuring Global Parameters Using the Setup Facility Configuring Host Name Configuring Protocols Configuring Network InterfacesConfiguring Line Card Interfaces Milo# show version Enter the enable command and password if prompted Using Global Configuration ModeMilo# configure terminal Verifying Running Configuration File SettingsMilo# copy running-config startup-config Router# show running-configSaving the Running Configuration Settings to Nvram Viewing the Running Configuration Settings Configuring the Software Configuration Register Bit Number Hexadecimal Value Meaning/Function Boot Field Setting Software Configuration SettingsCiscobootfieldvalue-processorname Changing Software Configuration Register Settings Miloconfig# config-register 0xvalue Reboot the systemLow-Order Bits in the Software Configuration Register Action/Filename Bit Bit Address net host High-Order Bits in the Software Configuration Register9600 Rommon 1 config-register Recovering a Lost PasswordEnter the initialize command to initialize the router Milo# show startup-config Installing and Removing a Flash Memory Card Using RP Flash Memory CardsOL-11496-01 Installing and Removing a Flash Memory Card Milo# format slot0 Formatting a New Flash Memory CardSpecifying a Cisco IOS Software Image to Boot the System Cd Command Flash Memory CommandsPwd Command Milo# dir slot0 Dir CommandDelete Command Milo# squeeze slot0 Squeeze CommandCopying Image Files to or From Flash Memory Booting from Flash MemoryMiloconfig# boot system flash slot0myfile1 Milo# copy tftpmyfile1 slot0myfile1 Milo# copy tftpfilename bootflashslot0slot1 filenameCopying a Cisco IOS Software Image into a Flash Memory Card Milo# copy tftpnew.image slot0new.image Milo# copy slot1image.new slot0image.new Copying Cisco IOS Software Images Between Flash Memory CardsMilo# configure terminal Copy startup-config slot0 slot1 filename Milo# show bootvarMilo# copy startup-config slot0myfile2 Milo# copy running-config slot0myfile2 Copy running-config slot0slot1filenameMilo# copy startup-config running-config Copy slot0slot1filename startup-configMilo# copy slot0myfile startup-config Recovering from Locked Blocks in Flash Memory Cards Post-Installation Procedures OL-11496-01