Cisco Systems 12810 manual Verifying Running Configuration File Settings, Milo# configure terminal

Page 28

Chapter 4 System Startup and Basic System Configuration

Cisco IOS User Interface

Step 3 Enter the configure terminal command to enter global configuration mode.

Milo# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Milo(config)#

Step 4 Enter the interface type slot/port command to enter interface configuration mode.

Milo(config)# interface type slot/port

Milo(config-if)#

Step 5 Enter the copy running-config startup-config command to save your configuration settings.

Milo# copy running-config startup-config

Your system is now minimally configured and able to boot using the configuration you entered.

Verifying Running Configuration File Settings

The show running-configcommand lets you check the settings in the running configuration file.

The following example displays the output for a Quad OC-3c/STM-1c POS interface installed in slot 1.

router# show running-config

Building configuration...

Current configuration:

!

version 12.0 no service pad

no service udp-small-servers no service tcp-small-servers

!

hostname Milo

!

enable secret 5 $1$W6K5$W/p5Bq6IPLGJ/hS9VVP1g. enable password twink

		interface POS1/0
		ip address 10.1.1.1 255.255.255.0
		crc 32
		Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

4-28		OL-11496-01

Image 28

Contents System Startup and Basic System Configuration Preconfiguration Requirements Sources of Cisco IOS SoftwareBoot Process Overview Powering On the Router and Observing the Boot Process Processor LED Display1 Meaning SourceLED Display Meaning Source PRIMII Meaning Source Line Card Alphanumeric LED Displays-Partial View ShownRomi OL-11496-01 Manually Booting the System Booting from the Cisco IOS Software Image Dir bootflashLocating a Valid Cisco IOS Software Image Dir slot0Command Purpose Boot flashConfiguring the Router Cisco IOS User Interface Command Modes Cisco IOS User InterfaceUser Exec Mode Privileged Exec ModeGlobal Configuration Mode Interface Configuration ModeUsing Setup for Configuration Changes Subinterface Configuration ModeMay enter a question mark ? for help SDCC1/0 No ip routing Configuring Global Parameters Using the Setup Facility Configuring Host Name Configuring Network Interfaces Configuring ProtocolsConfiguring Line Card Interfaces Milo# show version Using Global Configuration Mode Enter the enable command and password if promptedVerifying Running Configuration File Settings Milo# configure terminalMilo# copy running-config startup-config Router# show running-configSaving the Running Configuration Settings to Nvram Viewing the Running Configuration Settings Configuring the Software Configuration Register Bit Number Hexadecimal Value Meaning/Function Setting Software Configuration Settings Boot FieldCiscobootfieldvalue-processorname Changing Software Configuration Register Settings Reboot the system Miloconfig# config-register 0xvalueLow-Order Bits in the Software Configuration Register Action/Filename Bit High-Order Bits in the Software Configuration Register Bit Address net host9600 Recovering a Lost Password Rommon 1 config-registerEnter the initialize command to initialize the router Milo# show startup-config Using RP Flash Memory Cards Installing and Removing a Flash Memory CardOL-11496-01 Installing and Removing a Flash Memory Card Formatting a New Flash Memory Card Milo# format slot0Specifying a Cisco IOS Software Image to Boot the System Pwd Command Flash Memory CommandsCd Command Delete Command Dir CommandMilo# dir slot0 Squeeze Command Milo# squeeze slot0Miloconfig# boot system flash slot0myfile1 Booting from Flash MemoryCopying Image Files to or From Flash Memory Milo# copy tftpfilename bootflashslot0slot1 filename Milo# copy tftpmyfile1 slot0myfile1Copying a Cisco IOS Software Image into a Flash Memory Card Milo# copy tftpnew.image slot0new.image Copying Cisco IOS Software Images Between Flash Memory Cards Milo# copy slot1image.new slot0image.newMilo# configure terminal Milo# show bootvar Copy startup-config slot0 slot1 filenameMilo# copy startup-config slot0myfile2 Copy running-config slot0slot1filename Milo# copy running-config slot0myfile2Milo# copy slot0myfile startup-config Copy slot0slot1filename startup-configMilo# copy startup-config running-config Recovering from Locked Blocks in Flash Memory Cards Post-Installation Procedures OL-11496-01